CS5101A
ANALOG CHARACTERISTICS (T = T
to T
; VA+, VD+ = 5V; VA-, VD- = -5V;
A
MIN
MAX
VREF = 4.5V; Full-Scale Input Sinewave, 1 kHz; CLKIN = 4 MHz for -16, 8 MHz for -8; f = 50 kHz for -16,
s
100 kHz for -8; Bipolar Mode; FRN Mode; AIN1 and AIN2 tied together, each channel tested separately; Analog
Source Impedance = 50 Ω with 1000 pF to AGND unless otherwise specified)
CS5101A-J,K
CS5101A-A,B
CS5101A-S,T
Parameter*
Specified Temperature Range
Accuracy
Min Typ Max Min Typ Max Min Typ Max Units
0 to +70
-40 to +85
-55 to +125
°C
Linearity Error
-J,A,S
-K,B,T
Drift
(Note 1)
(Note 2)
-
-
-
0.002 0.003
0.001 0.002
-
-
-
0.002 0.003
0.001 0.002
-
-
-
0.002 0.004 %FS
0.001 0.003 %FS
-
-
-
± 1/4
-
± 1/4
-
± 1/2
-
∆LSB
Bits
Differential Linearity
Full Scale Error
(Notes 3, 4) 16
-
16
-
-
-
16
-
-
-
-J,A,S
-K,B,T
Drift
(Note 1)
-
-
-
LSB
LSB
∆LSB
± 1
± 1
± 1
± 2
± 2
± 1
± 2
± 2
± 1
± 4
± 3
-
± 1
± 1
± 1
± 2
± 2
± 1
± 2
± 2
± 2
± 4
± 3
-
± 2
± 2
± 2
± 2
± 2
± 2
± 2
± 2
± 2
± 5
± 4
-
(Note 2)
(Note 1)
-
-
Unipolar Offset
Bipolar Offset
-J,A,S
-K,B,T
Drift
-
-
-
-
-
-
-
-
-
LSB
LSB
∆LSB
± 5
± 4
-
± 5
± 4
-
± 5
± 4
-
(Note 2)
(Note 1)
-J,A,S
-K,B,T
Drift
-
-
-
-
-
-
-
-
-
LSB
LSB
∆LSB
± 5
± 3
-
± 5
± 3
-
± 5
± 3
-
(Note 2)
Bipolar Negative Full-Scale Error
-J,A,S
-K,B,T
Drift
(Note 1)
(Note 2)
-
-
-
-
-
-
-
-
-
LSB
LSB
∆LSB
± 1
± 1
± 1
± 4
± 3
-
± 1
± 1
± 1
± 4
± 3
-
± 1
± 1
± 2
± 5
± 3
-
Dynamic Performance (Bipolar Mode)
Peak Harmonic or Spurious Noise (Note 1)
1 kHz Input
-J,A,S
-K,B,T
-J,A,S
-K,B,T
96
98
85
85
-
100
102
88
91
0.002
0.001
-
-
-
-
-
-
96
98
85
85
-
100
102
88
91
0.002
0.001
-
-
-
-
-
-
94
98
83
85
-
100
102
88
91
0.002
0.001
-
-
-
-
-
-
dB
dB
dB
dB
%
12 kHz Input
Total Harmonic Distortion -J,A,S
-K,B,T
-
-
-
%
Signal-to-Noise Ratio
(Note 1)
(Note 5)
0dB Input
-60 dB Input
Noise
-J,A,S
-K,B,T
-J,A,S
-K,B,T
87
90
-
90
92
30
32
-
-
-
-
87
90
-
90
92
30
32
-
-
-
-
87
90
-
90
92
30
32
-
-
-
-
dB
dB
dB
dB
-
-
-
Unipolar Mode
Bipolar Mode
-
-
35
70
-
-
-
-
35
70
-
-
-
-
35
70
-
-
µV
µV
rms
rms
Notes: 1. Applies after calibration at any temperature within the specified temperature range. At temp
2. Total drift over specified temperature range after calibration at power-up at 25 °C.
3. Minimum resolution for which no missing codes is guaranteed over the specified temperature range.
4. Clock speeds of less than 1.0 MHz, at temperatures >100°C will degrade DNL performance.
5. Wideband noise aliased into the baseband. Referred to the input.
*Refer to Parameter Definitions (immediately following the pin descriptions at the end of this data sheet).
Specifications are subject to change without notice.
2
DS45F2
CIRRUS [ CIRRUS LOGIC ]
