欢迎访问ic37.com |
会员登录 免费注册
发布采购

BMA253 参数 Datasheet PDF下载

BMA253图片预览
型号: BMA253
PDF下载: 下载PDF文件 查看货源
内容描述: [3轴 12bit 加速度传感器]
分类和应用: 传感器
文件页数/大小: 119 页 / 2014 K
品牌: BOSCH [ Bosch Sensortec GmbH ]
 浏览型号BMA253的Datasheet PDF文件第21页浏览型号BMA253的Datasheet PDF文件第22页浏览型号BMA253的Datasheet PDF文件第23页浏览型号BMA253的Datasheet PDF文件第24页浏览型号BMA253的Datasheet PDF文件第26页浏览型号BMA253的Datasheet PDF文件第27页浏览型号BMA253的Datasheet PDF文件第28页浏览型号BMA253的Datasheet PDF文件第29页  
BMA253  
Data sheet  
Page 25  
4.6 Non-volatile memory  
The entire memory of the BMA253 consists of three different kinds of registers: hard-wired,  
volatile, and non-volatile. Part of it can be both read and written by the user. Access to non-  
volatile memory is only possible through (volatile) image registers.  
Altogether, there are eight registers (octets) with NVM backup which are accessible by the user.  
The addresses of the image registers range from 0x38 to 0x3C. While the addresses up to  
0x3A are used for offset compensation (see 4.4 Offset Compensation), addresses 0x3B and  
0x3C are general purpose registers not linked to any sensor-specific functionality.  
The content of the NVM is loaded to the image registers after a reset (either POR or softreset)  
or after a user request which is performed by writing ´1´ to the write-only bit (0x33) nvm_load.  
As long as the image update is in progress, bit (0x33) nvm_rdy is ´0´, otherwise it is ´1´.  
The image registers can be read and written like any other register.  
Writing to the NVM is a three-step procedure:  
1. Write the new contents to the image registers.  
2. Write ´1´ to bit (0x33) nvm_prog_mode in order to unlock the NVM.  
3. Write ´1´ to bit (0x33) nvm_prog_trig and keep ´1´ in bit (0x33) nvm_prog_mode in order  
to trigger the write process.  
Writing to the NVM always renews the entire NVM contents. It is possible to check the write  
status by reading bit (0x33) nvm_rdy. While (0x33) nvm_rdy = ´0´, the write process is still in  
progress; if (0x33) nvm_rdy = ´1´, then writing is completed. As long as the write process is  
ongoing, no change of power mode and image registers is allowed. Also, the NVM write cycle  
must not be initiated while image registers are updated, in low-power mode, and in suspend  
mode.  
Please note that the number of permitted NVM write-cycles is limited as specified in Table 1.  
The number of remaining write-cycles can be obtained by reading bits (0x33) nvm_remain.  
BST-BMA253-DS000-01 | Revision 1.0 | August 2015  
Bosch Sensortec  
© Bosch Sensortec GmbH reserves all rights even in the event of industrial property rights. We reserve all rights of disposal such as copying and passing on to  
third parties. BOSCH and the symbol are registered trademarks of Robert Bosch GmbH, Germany.  
Note: Specifications within this document are subject to change without notice.  
 复制成功!