Punched Carrier Configuration
8 & 12 mm Tape Only
CONSTANT DIMENSIONS
Tape
Size
D
0
E
P
0
P
2
T
1
G
1
G
2
R
MIN.
25
8mm 1.5
+0.1
-0.0
1.75 ± 0.10
4.0 ± 0.10
2.0 ± 0.05
0.10 0.75 0.75
and (0.059
+0.004
) (0.069 ± 0.004) (0.157 ± 0.004) (0.079 ± 0.002) (0.004) (0.030) (0.030) (0.984)
-0.000
See
Max. Min.
Min. Note 2
12mm
8 & 12 MM PUNCHED TAPE
METRIC DIMENSIONS WILL GOVERN
VARIABLE DIMENSIONS
Tape Size
8mm
12mm
8mm
1/2 Pitch
12mm
Double
Pitch
P
1
F
W
+0.3
8.0
-0.1
+0.012
(0.315
-0.004
)
A
0
B
0
See Note 1
T
See Note 3
4.0 ± 0.10
3.5 ± 0.05
(0.157 ±0 .004) (0.138 ± 0.002)
4.0 ± .010
5.5 ± 0.05
12.0 ± 0.3
(0.157 ± 0.004) (0.217 ± 0.002) (0.472 ± 0.012)
+0.3
2.0 ± 0.10
3.5 ± 0.05
8.0
-0.1
+0.012
(0.079 ± 0.004) (0.138 ± 0.002) (0.315
-0.004
)
8.0 ± 0.10
5.5 ± 0.05
12.0 ± 0.3
(0.315 ± 0.004) (0.217 ± 0.002) (0.472 ± 0.012)
NOTES:
1. A
0
, B
0
, and T are determined by the max. dimensions to the ends of the terminals
extending from the component body and/or the body dimensions of the component.
The clearance between the ends of the terminals or body of the component to the sides
and depth of the cavity (A
0
, B
0
, and T) must be within
0.05 mm (.002) min. and 0.50 mm (.020) max. The
clearance allowed must also prevent rotation of the
component within the cavity of not more than 20
degrees (see sketches A & B).
2. Tape with components shall pass around radius “R”
without damage.
3. 1.1 mm (.043) Base Tape and 1.6 mm (.063) Max.
for Non-Paper Base Compositions.
BAR CODE LABELING STANDARD
AVX bar code labeling is available and follows latest version of EIA-556-A.
AUTOMATIC INSERTION PACKAGING TAPE & REEL
All tape and reel specifications are in compliance with EIA 481A.
(equivalent to IEC 286 part 3).
• 8mm carrier
• Reeled quantities: Reels of 3,000 per 7" reel or 10,000 pieces per
13" reel 0402 = 5,000 pieces per 7" reel and
20,000 pieces per 13" reel
G MAX.
B*
A
D*
C
E
CARRIER DIMENSIONS:
A
B
C
D
millimeters (inches)
E
1.5
FULL RADIUS
*
DRIVE SPOKES OPTIONAL
IF USED, ASTERISKED
DIMENSIONS APPL
Y.
E
F
TOP
TAPE
L
P
DIRECTION OF FEED
CENTER LINES
OF CAVITY
D
F
+0.1
-0.0
+0.004
(0.059
-0.000
)
8.0 ± 0.3
3.5 ± 0.05
1.75±0.1
2.0 ± 0.05
4.0 ± 0.1
(0.315 ± 0.012) (0.138 ± 0.002) (0.069 ± 0.004) (0.079 ± 0.002) (0.157 ± 0.004)
F
Note: The nominal dimensions of the component compartment (W,L) are derived from
the component size.
REEL DIMENSIONS:
A
(1)
B
C
D
millimeters (inches)
E
F
G
10 PITCHES
CUMULATIVE
TOLERANCE ON
TAPE
±0.2
C
180±1.0
1.5 min.
13±0.2
20.2 min.
50 min.
9.6±1.5
14.4 max.
(7.087±0.039) (0.059 min.) (0.512 ± 0.008) (0.795 min.) (1.969 min.) (0.370 ± 0.050) (0.567 max.)
Metric dimensions will govern.
Inch measurements rounded and for reference only.
(1) 330mm (13 inch) reels are available.
W
B
A
P = 4mm except 0402 where P = 2mm
NOTE: AVX reserves the right to change the information
published herein without notice.
56
AVX [ AVX CORPORATION ]
