Packaging of Chip Components
Automatic Insertion Packaging
TAPE & REEL QUANTITIES
All tape and reel specifications are in compliance with RS481.
Embossed or
Punched Carrier
Embossed Only
Punched Only
Qty. per Reel/
7" Reel
Qty. per Reel/
13" Reel
(1)
REEL DIMENSIONS
12mm
8mm
CDR33, CDR31,
CDR32, CDR01
0504, 0907
0402, 0603
2,000 or 4,000 (1)
10,000
3,000
10,000
CDR03, CDR02 CDR04, CDR34
CDR05, CDR35
CDR06
1,000
4,000
Dependent on chip thickness.
Tape
Size
(1)
8mm
A
Max.
B*
Min.
C
D*
Min.
N
Min.
W
1
W
2
Max.
W
3
7.9 Min.
+1.0
330
1.5
13.0±0.20
20.2
50
8.4
–0.0
14.4
(0.311)
(12.992) (0.059) (0.512±0.008) (0.795) (1.969) (0.331
+0.060
) (0.567) 10.9 Max.
–0.0
(0.429)
8 & 12 MM EMBOSSED TAPE
METRIC DIMENSIONS WILL GOVERN
11.9 Min.
+2.0
18.4
(0.469)
330
1.5
13.0±0.20
20.2
50
12.4
–0.0
12mm
(12.992) (0.059) (0.512±0.008) (0.795) (1.969) (0.488
+0.076
) (0.724) 15.4 Max.
–0.0
(0.607)
Metric dimensions will govern.
English measurements rounded and for reference only.
(1)
For tape sizes 16mm and 24mm (used with chip size 3640)
consult EIA RS-481 latest revision.
EMBOSSED CARRIER CONFIGURATION
8 & 12 MM TAPE ONLY
VARIABLE DIMENSIONS
Tape B
1
D
1
Size Max. Min.
S
ee See
Note 6 Note 5
CONSTANT DIMENSIONS
R
Min.
See
Note 2
+0.3
F
P
1
T
2
W
A
0
B
0
K
0
See
Note1
Tape
Size
D
0
E
P
0
P
2
T
Max.
T
1
G
1
G
2
0.75
(.030)
Min.
See
Note 4
4.55
1.0
3.5 ± 0.05
4.0 ± 0.10
25 2.5 Max. 8.0
-0.1
8mm
(0.179) (0.039) (0.138 ± 0.002) (0.157 ± 0.004) (0.984) (0.098) (0.315
+0.012
)
-0.004
8.4
+1.0
1.75 ± 0.10
4.0 ± 0.10
2.0 ± 0.05
0.600 0.10 0.75
-0.0
8mm
and (0.059
+0.004
) (0.069 ± 0.004) (0.157 ± 0.004) (0.079 ± 0.002) (0.024) (0.004) (.030)
-0.0
12mm
Max. Min.
See
Note 3
8.2
1.5
5.5 ± 0.05
4.0 ± 0.10
30 6.5 Max. 12.0 ± .30
See
12mm (0.323) (0.059) (0.217 ± 0.002) (0.157 ± 0.004) (1.181) (0.256) (0.472 ± 0.012) Note 1
8mm
+0.3
4.55
1.0
3.5 ± 0.05
2.0 ± 0.10
25 2.5 Max. 8.0
-0.1
1/2
+0.012
Pitch (0.179) (0.039) (0.138 ± 0.002) (0.79 ± 0.004) (0.984) (0.098) (0.315
-0.004
)
12mm
8.2
1.5
5.5 ± 0.05
8.0 ± 0.10
30 6.5 Max. 12.0 ± .30
Double
(0.323) (0.059) (0.217 ± 0.002) (0.315 ± 0.004) (1.181) (0.256) (0.472 ± 0.012)
Pitch
See
Note 1
See
Note 1
NOTES:
1. A
0
, B
0
, and K
0
are determined by the max. dimensions to the ends of the terminals extending from the component body and/or the body dimensions of the component. The
clearance between the end of the terminals or body of the component to the sides and depth of the cavity (A
0
, B
0
, and K
0
) must be within 0.05 mm (.002) min. and 0.50 mm
(.020) max. The clearance allowed must also prevent rotation of the component within the cavity of not more than 20 degrees (see sketches C & D).
2. Tape with components shall pass around radius “R” without damage. The minimum trailer length (Note 2 Fig. 3) may require additional length to provide R min. for 12 mm
embossed tape for reels with hub diameters approaching N min. (Table 4).
3. G
1
dimension is the flat area from the edge of the sprocket hole to either the outward deformation of the carrier tape
between the embossed cavities or to the edge of the cavity whichever is less.
4. G
2
dimension is the flat area from the edge of the carrier tape opposite the
sprocket holes to either the outward deformation of the carrier tape between the
embossed cavity or to the edge of the cavity whichever is less.
5. The embossment hole location shall be measured from the sprocket hole con-
trolling the location of the embossment. Dimensions of embossment location and
hole location shall be applied independent of each other.
6. B
1
dimension is a reference dimension for tape feeder clearance only.
55
AVX [ AVX CORPORATION ]
