3
■
Specifications
Measurement method:
Resistance
A/D method:
Display:
Auto-ranging:
Input overrange:
Sampling rate:
[FAST]
[MEDIUM]
[SLOW]
Response time:
[FAST]
[MEDIUM]
[SLOW]
AC (1kHz ± 0.2Hz) 4-terminal method
• Buzzer output:
∑-∆ method with sample hold function
Fluorescent character display tube.
Resistance [31000], voltage [50000] counter
Provided (disabled when comparator is ON)
" OF " display
50 Hz
50 times/s
6.25 times/s
1.56 times/s
50 Hz
100 ms
800 ms
1.92 s
60 Hz
60 times/s
7.52 times/s
1.88 times/s
60 Hz
84 ms
667 ms
1.60 s
(ON/OFF setting possible)
[Resistance measurement mode]: Switchable between Hi, Lo and IN.
[Resistance/voltage measurement mode]: Switchable between PASS and FAIL.
Maximum input voltage:
DC 60 V max. (AC input is not possible)
Withstand voltage:
Between power supply line and protective ground terminal /
AC 2.3 kV rms for 1 minute
comparator results, measurement termination, measurement
irregularity signal
printer, zero-adjustment, comparator number selection,
external power supply possible (DC 5 V to 24 V)
External output terminals:
[Open-collector output] (DC 35V-50mA max.)
Measurement irregularity:
" ---- " display
(NG: External output of measurement irregularity signal)
External control terminal:
[CMOS input] Measurement trigger, comparator trigger,
Interfaces:
RS-232C (standard), GP-IB or printer interface [Centronics]
(option)
to 104˚F) , 80% RH or less.
Storage temperature and humidity range: -10 to 50
˚C
(14˚F
to 122˚F) , 80% RH or less.
Operating conditions: Indoors, below an altitude of 2000 m.
AC 100V to 240V (±10%), automatic voltage selection, 50/60Hz
Environment conditions:
Operating temperature and humidity range: 0 to 40
˚C
(32˚F
(no condensation)
(When non-conductive resistance is measured. The response time
differs depending on the measured object.)
Comparator:
Comparator output (Resistance/voltage measurement mode)
Resistance
Voltage
Power supply:
Maximum rated power:
30 VA
Dimensions and mass:
215(W)
×
80(H)
×
320(D)mm, 2.1kg / [8.5"(W)
×
3.1"(H)
×
12.6"(D), 74.1 oz.]
(not including options)
Included accessory:
9287-10 CLIP TYPE LEADS (1)
EN61326:1997+A1:1998+A2:2001
EN61000-3-2:2000
EN61000-3-3:1995+A1:2001
EN61010-1:2001
Pollution degree: level 2
Conforming standards:
EMC
Safety
Hi
FAIL (red)
FAIL (red)
FAIL (red)
IN
FAIL (red)
PASS (green)
FAIL (red)
Lo
FAIL (red)
(FAIL) (red)
FAIL (red)
Hi
IN
Lo
• Mode switch:
• Comparator points:
* Restricted to Hi, IN, Lo in the resistance measurement mode.
Up to 30 comparator condition settings can be memorized.
Switchable between AUTO and MANU.
■
Measurement Ranges
Range
Maximum
display value
Conditions for guaranteed accuracy: at 23˚C±5˚C[73.4˚F
±9˚F],
80% RH (no condensation), following 30 min.
warming-up, and after zero adjustment
[Resistance measurement]
(Sampling speed : SLOW)
30mΩ
31.000mΩ
1µΩ
7.4mA
300mΩ
310.00mΩ
10µΩ
1mA
3Ω
3.1000Ω
100µΩ
100µA
30Ω
31.000Ω
1mΩ
10µA
300Ω
310.00Ω
10mΩ
5µA
3kΩ
3.1000kΩ
100mΩ
1.5µA
[Voltage measurement]
(Sampling speed : SLOW)
Range
Maximum
display
DC 5V
±5.0000V
100µV
±0.05%rdg. ±5dgt.
DC 50V
±50.000V
1mV
±0.05%rdg. ±5dgt.
Resolution
Measurement
current
Resolution
Accuracy
Temperature
modules
Accuracy
Temperature
modules
Open-terminal
voltage
±0.5%rdg.±8dgt.
* In the case of MEDIUM: Add 3 dgt. to the above dgt. error
FAST: ±0.5% rdg. ±8 dgt. (30 mΩ)/±0.5% rdg. ±6 dgt. (other ranges)
However, in the case of FAST, the display counter decreases 4 digits in all ranges.
(±0.05% rdg. ±0.8 dgt.)/˚C (1.8˚F) *FAST: 300m to 3kΩ range (±0.05% rdg. ± 0.6 dgt.)/˚C (1.8˚F)
20 mV peak max. (when limiter is ON)
(±0.005% rdg. ±0.5 dgt.)/˚C (1.8˚F)
* MEDIUM: Add 3 dgt. to the accuracy dgt. error
FAST: Add 5 dgt. to the accuracy dgt. error
* During charging, the measurement value may be unsteady due to
ripple voltage.
* Resistance with inductance elements may not always be
measurable.
3560 AC mΩ HiTESTER
9452 CLIP TYPE LEADS
9453 FOUR TERMINAL LEADS
9454 ZERO ADJUSTMENT BOARD
(for 9461,9465)
9455 PIN TYPE LEADS
(for high-density use)
9461 PIN TYPE LEADS
9465 PIN TYPE LEADS
9466 REMOTE CONTROL SWITCH
9467 LARGE CLIP TYPE LEADS
9770 PIN TYPE LEADS
9771 PIN TYPE LEADS
*
Non CE mark.
*
9588 GP-IB INTERFACE
9151-02 GP-IB CONNECTION CABLE
(2 meters)
9151-04 GP-IB CONNECTION CABLE
(4 meters)
9589 PRINTER INTERFACE
9203 DIGITAL PRINTER
9425 CONNECTION CORD
(20-pin half-pitch—36pin/D-sub)
9233
[for connecting the 3560 to the 9203/2meters]
RECORDING PAPER
(for the 9203/10meters,10rolls)
9287-10 (included)
9452
9453
●
Options
same appearance
as 9461
0.8 dia.
Tip
magnified
view
9455
Current side
Voltage side
0.2/0.2 dia.
Approx. 85 cm
between connectors,
and 8 cm between
probes
Approx. 80 cm
between connectors,
and 20 cm between
probes
Approx. 80 cm
between connectors,
and 30 cm between
probes
Approx. 40 cm
between connectors,
and 25 cm between
probes
9461
9465 & 9466
9467
9454
For zero-adjustment
when 9461 or 9465 is
used.
Approx. 40 cm
between connectors,
and 25 cm between
probes
Cable length :
connectors to lead
branch approx. 1.7m,
lead branch to probes
approx. 10 cm
Approx. 85 cm between
connectors, and 25 cm
between probes, 29 mm
dia.
9770/9771
9770 -- in detail
9771 -- in detail
9 mm
Cable length:
connector to fork
40cm, fork to probes
25cm
1.8 mm dia.
2 mm
0.6 mm dia.
0.2 mm
2.2 mm
DISTRIBUTED BY
HEAD OFFICE :
81 Koizumi, Ueda, Nagano, 386-1192, Japan
TEL +81-268-28-0562 / FAX +81-268-28-0568
E-mail: os-com@hioki.co.jp
HIOKI USA CORPORATION :
6 Corporate Drive, Cranbury, NJ 08512 USA
TEL +1-609-409-9109 / FAX +1-609-409-9108
E-mail: hioki@hiokiusa.com
Shanghai Representative Office :
1310 Shanghai Times Square Office
93 Huaihai Zhong Road
Shanghai, 200021, P.R.China
TEL +86-21-6391-0090, 0092
FAX +86-21-6391-0360
E-mail: info@hioki.cn
All information correct as of Mar. 3, 2006. All specifications are subject to change without notice.
3560E3-63B-03K
7.4 mm
9 mm
Printed in Japan
ASM-SENSOR [ ASM GMBH ]
