欢迎访问ic37.com |
会员登录 免费注册
发布采购

AS1310_12 参数 Datasheet PDF下载

AS1310_12图片预览
型号: AS1310_12
PDF下载: 下载PDF文件 查看货源
内容描述: 超低静态电流,滞回DC-DC升压转换器 [Ultra Low Quiescent Current, Hysteretic DC-DC Step-Up Converter]
分类和应用: 转换器升压转换器
文件页数/大小: 20 页 / 1598 K
品牌: AMSCO [ AMS(艾迈斯) ]
 浏览型号AS1310_12的Datasheet PDF文件第10页浏览型号AS1310_12的Datasheet PDF文件第11页浏览型号AS1310_12的Datasheet PDF文件第12页浏览型号AS1310_12的Datasheet PDF文件第13页浏览型号AS1310_12的Datasheet PDF文件第15页浏览型号AS1310_12的Datasheet PDF文件第16页浏览型号AS1310_12的Datasheet PDF文件第17页浏览型号AS1310_12的Datasheet PDF文件第18页  
AS1310  
Datasheet - Application Information  
9.1.1 Power-OK and Low-Battery-Detect Functionality  
LBO goes low in startup mode as well as during normal operation if:  
- The voltage at the LBI pin is below LBI threshold (0.6V). This can be used to monitor the battery voltage.  
- LBI pin is connected to GND and VOUT is below 92.5% of its nominal value. LBO works as a power-OK signal in this case.  
The LBI pin can be connected to a resistive-divider to monitor a particular definable voltage and compare it with a 0.6V internal reference. If LBI  
is connected to GND an internal resistive-divider is activated and connected to the output. Therefore, the Power-OK functionality can be realized  
with no additional external components.  
The Power-OK feature is not active during shutdown and provides a power-on-reset function that can operate down to VIN = 0.7V. A capacitor to  
GND may be added to generate a power-on-reset delay. To obtain a logic-level output, connect a pull-up resistor R3 from pin LBO to pin VOUT.  
Larger values for this resistor will help to minimize current consumption; a 100kΩ resistor is perfect for most applications (see Figure 16 on page  
13).  
For the circuit shown in the left of Figure 15, the input bias current into LBI is very low, permitting large-value resistor-divider networks while  
maintaining accuracy. Place the resistor-divider network as close to the device as possible. Use a defined resistor for R2 and then calcuate R1  
as:  
VIN  
----------  
R1 = R2 ⋅  
1  
(EQ 18)  
VLBI  
Where:  
VLBI is 0.6V ±30mV  
Figure 15. Typical Application with Adjustable Battery Monitoring  
L1  
6.8µH  
LX  
3
VIN  
0.7V to 3.6V  
Low Battery Detect  
8
6
VIN  
O  
R3  
C1  
22µF  
R1  
R2  
VOUT  
1.8V to 3.3V  
4
1
AS1310  
VOUT  
LBI  
C2  
22µF  
5
7
On  
Off  
REF  
EN  
CREF  
100nF  
GND  
2
Figure 16. Typical Application with LBO orkinas Power-OK  
L1  
6.8µH  
LX  
3
VIN  
0.7V to 3.6V  
Low Battery Detect  
8
6
VIN  
LBO  
R3  
C1  
22µF  
VOUT  
1.8V to 3.3V  
4
1
AS1310  
VOUT  
LBI  
C2  
22µF  
5
7
On  
Off  
REF  
EN  
CREF  
100nF  
GND  
2
www.austriamicrosystems.com/DC-DC_Step-Up/AS1310  
Revision 1.8  
13 - 19