欢迎访问ic37.com |
会员登录 免费注册
发布采购

AS1112B 参数 Datasheet PDF下载

AS1112B图片预览
型号: AS1112B
PDF下载: 下载PDF文件 查看货源
内容描述: 16通道LED驱动器,具有点校正和灰度PWM [16-Channel LED Driver with Dot Correction and Greyscale PWM]
分类和应用: 驱动器
文件页数/大小: 18 页 / 611 K
品牌: AMSCO [ AMS(艾迈斯) ]
 浏览型号AS1112B的Datasheet PDF文件第6页浏览型号AS1112B的Datasheet PDF文件第7页浏览型号AS1112B的Datasheet PDF文件第8页浏览型号AS1112B的Datasheet PDF文件第9页浏览型号AS1112B的Datasheet PDF文件第11页浏览型号AS1112B的Datasheet PDF文件第12页浏览型号AS1112B的Datasheet PDF文件第13页浏览型号AS1112B的Datasheet PDF文件第14页  
AS1112  
Datasheet - Detailed Description  
Figure 8. Error Detection Timing (GS=FFFFHEX, DC=3FHEX  
)
LD  
>1µs  
OEN  
GSCLK  
SID  
LODn, LSDn  
LODn+1, LSDn+1  
Error  
Detection  
Start  
Error  
Detection  
End  
Note: The rising edge of LD latches new data into the internal registers depending on the logic level of the pin  
MODE. If the pin MODE is tied GND, the greyscale registers are updated. If the pin MODE is tied to VCC, the  
dot correction registers are updated.  
Delay Between Outputs  
The AS1112 uses graduated delay circuits between OUTn outputs. These circuits are contained in the constant-current  
driver block of the AS1112 (see Figure 1 on page 1). The average-delay time is 30ns (typ).  
The maximum delay is 450ns (typ) from OUT0 to OUT15. The delay scheme works by switching on and switching off  
each output channel. Thus the on/off time of each channel is the same regardless of the delay. These delays prevent  
large inrush currents and switching noise that can reduce bypass capacitance when the outputs are switched on.  
OUTn Enable  
All OUTn channels can be collectively switched off with one signal. When OEN is set to 1, all OUTn channels are dis-  
abled, regardless of the device logic operations. The greyscale counter is also reset when OEN is set to 1.  
When OEN is set to 0, all OUTn channels are in normal operation.  
Table 10. Pin OEN Truth Table  
OEN  
OUT0:OUT15  
Normal Operation  
Disabled  
0
1
Setting Maximum Channel Current  
The maximum output current per channel is programmed by a single resistor, RIREF, which is placed between pin IREF  
and GND. The voltage on pin IREF is set by an internal band gap VIREF (1.24V typ). The maximum channel current is  
equivalent to the current flowing through RIREF multiplied by a factor of 31.5. The maximum output current is calculated  
as:  
VIREF  
IMAX =  
x 31.5  
(EQ 1)  
RIREF  
Where:  
VIREF = 1.24V;  
RIREF = User-selected external resistor.  
Figure 5 on page 7 shows the maximum output current IOUT versus RIREF, where RIREF is the value of the resistor  
between IREF terminal to GND, and IOUT is the constant output current of OUT0:OUT15.  
www.austriamicrosystems.com  
Revision 1.06  
10 - 18