N04L1630C2B
AMI Semiconductor, Inc.
Absolute Maximum Ratings
1
Item
Voltage on any pin relative to V
SS
Voltage on V
CC
Supply Relative to V
SS
Power Dissipation
Storage Temperature
Operating Temperature
Soldering Temperature and Time
Symbol
V
IN,OUT
V
CC
P
D
T
STG
T
A
T
SOLDER
Rating
–0.3 to V
CC
+0.3
–0.3 to 4.5
500
–40 to 125
-40 to +85
260
o
C, 10sec
Unit
V
V
mW
o
C
o
C
o
C
Advance Information
1. Stresses greater than those listed above may cause permanent damage to the device. This is a stress rating only and functional operation of the
device at these or any other conditions above those indicated in the operating section of this specification is not implied. Exposure to absolute maximum
rating conditions for extended periods may affect reliability.
Operating Characteristics (Over Specified Temperature Range)
Item
Supply Voltage
Data Retention Voltage
Input High Voltage
Input Low Voltage
Output High Voltage
Output Low Voltage
Input Leakage Current
Output Leakage Current
Read/Write Operating Supply Current
@ 1
µs
Cycle Time
2
Read/Write Operating Supply Current
@ 70 ns Cycle Time
2
Page Mode Operating Supply Current
@ 70ns Cycle Time
2
(Refer to Power
Savings with Page Mode Operation)
Maximum Standby Current
3
Symbol
V
CC
V
DR
V
IH
V
IL
V
OH
V
OL
I
LI
I
LO
I
CC1
I
CC2
I
CC3
I
OH
= -100uA
I
OH
= -1mA
I
OL
= 100uA
I
OL
= 2.1mA
V
IN
= 0 to V
CC
OE = V
IH
or Chip Disabled
V
CC
=V
CC
Max, V
IN
=V
IH
or V
IL
Chip Enabled, I
OUT
= 0
V
CC
=V
CC
Max, V
IN
=V
IH
or V
IL
Chip Enabled, I
OUT
= 0
V
CC
=V
CC
Max, V
IN
=V
IH
or V
IL
Chip Enabled, I
OUT
= 0
V
IN
= V
CC
or 0V
Chip Disabled
t
A
= 85
o
C, V
CC
= 3.6 V
Vcc = 1.8V, V
IN
= V
CC
or 0
Chip Disabled, t
A
= 85
o
C
2.5
10
Chip Disabled
3
Test Conditions
Min.
2.7
1.8
0.7Vcc
–0.3
V
CC
–0.2
2.4
0.2
0.4
0.5
0.5
3.0
15.0
µA
µA
mA
mA
V
CC
+0.3
0.6
Typ
1
3.0
Max
3.6
Unit
V
V
V
V
V
V
V
4
8
mA
I
SB1
1
10.0
µA
Maximum Data Retention Current
3
I
DR
5
µA
1. Typical values are measured at Vcc=Vcc Typ., T
A
=25°C and not 100% tested.
2. This parameter is specified with the outputs disabled to avoid external loading effects. The user must add current required to drive output capacitance
expected in the actual system.
3. This device assumes a standby mode if the chip is disabled (CE1 high or CE2 low). In order to achieve low standby current all inputs must be within
0.2 volts of either VCC or VSS.
(DOC# 14-02-042 ReI I ECN# 01-1374
The specifications of this device are subject to change without notice. For latest documentation see http://www.amis.com.
AMI [ AMI SEMICONDUCTOR ]
