AMIS-40616
LIN Transceiver with 5V Voltage Regulator
Data Sheet
8.0 Electrical Characteristics
8.1 Definitions
All voltages are referenced to GND (Pin 13). Positive currents flow into the IC.
8.2 Absolute Maximum Ratings
Stresses above those listed in this clause may cause permanent device failure. Exposure to absolute maximum ratings for extended
periods may affect device reliability.
Table 5: Absolute Maximum Ratings
Symbol
Parameter
(1)
Vbb
Battery voltage on pin V
bb
Vcc
DC voltage on pin V
cc
I_Vcc
Current delivered by the V
cc
regulator
(2)
V_LIN
LIN bus voltage
V_INH
DC voltage on inhibit pin
V_WAKE
DC voltage on WAKE pin
V_Dig_in
DC input voltage on pins TxD, RxD, EN, STB
Tjunc
Maximum junction temperature
(3)
Vesd
Electrostatic discharge voltage (pins LIN, INH, WAKE, and V
bb
) system HBM
(4)
Electrostatic discharge voltage (pins LIN, INH, WAKE, and V
bb
) HBM
(4)
Electrostatic discharge voltage (other pins) HBM
(5)
Electrostatic discharge voltage; charge device model
Notes:
1.
2.
3.
4.
5.
Min.
-0.3
0
50
-40
-0.3
-45
-0.3
-40
-8
-4
-2.0
-250
Max.
+45
+7
+45
V
bb
+ 0.3
V
bb
+ 0.3
V
cc
+ 0.3
+165
+8
+4
+2.0
+250
Unit
V
V
mA
V
V
V
V
°C
kV
kV
kV
V
The applied transients shall be in accordance with ISO 7637 part 1, test pulses 1, 2, 3a, 3b, and 5. The device complies with functional class C; class A can be
reached depending on the application and external components.
The applied transients shall be in accordance with ISO 7637 part 1, test pulses 1, 2, 3a, and 3b. The device complies with functional class C; class A can be
reached depending on the application and external components.
Equivalent to discharging a 150pF capacitor through a 330Ω resistor conform to IEC Standard 1000-4-2. The specified values are a target to be verified on first
prototypes. Based on the evaluation results, additional external protection components might be recommended to reach the specified system ESD levels.
Equivalent to discharging a 100pF capacitor through a 1.5k
Ω
resistor conform to MIL STD 883 method 3015.7.
Conform to EOS/ESD-DS5.3 (socket mode).
8.3 DC Characteristics
V
BB
= 6V to 26V; T
junc
= -40°C to +150°C; unless otherwise specified.
Table 6: DC Characteristics Supply
Symbol
Parameter
Pins VBB and VCC
Ibb_ON
Supply current
Ibb_STB
Supply current
Ibb_SLP
Supply current
Regulator output voltage
Vcc_out
Regulator output voltage
Regulator output voltage
Iout_max_cont
Maximum output current
Iout_max_conta
Maximum output current
Iout_max_abs
Absolute maximum output current
Iout_lim
Over-current limitation
Conditions
Normal mode; LIN recessive
Stand-by mode, V
bb
= 6 – 18V
Sleep mode, V
bb
= 6 – 18V
Normal mode, V
cc
load 1mA-30mA
Normal mode, V
cc
load 0mA-50mA
Stand-by mode, V
cc
load 0mA-50mA
V
bb
= 16V; Tamb = 105°C
V
bb
= 26V; limited lifetime
Thermal shutdown can occur
Min.
Typ.
Max.
1
60
20
5.1
5.17
5.2
30
30
50
150
Unit
mA
µA
µA
V
V
V
mA
mA
mA
mA
4.9
4.83
4.8
5.0
5.0
5.0
50
AMI Semiconductor
– January 2007, M-20545-001
9
www.amis.com
AMI [ AMI SEMICONDUCTOR ]
