Revision 5.01 – November 30, 2005
S5335 – PCI Bus Controller, 3.3V
Data Sheet
Single Cycle Pass-Thru Reads
within one of its defined Pass-Thru regions, it indicates
to the Add-On that a write to the Pass-Thru Data Reg-
ister (APTD) is required.
A single cycle Pass-Thru read operation occurs when
a PCI initiator reads a single value from a Pass-Thru
region. PCI single cycle transfers consists of an
address phase and a one data phase. During the ad-
dress phase of the PCI transfer, the S5335 stores the
PCI address into the Pass-Thru Address Register
(APTA). If the S5335 determines that the address is
Figure 85 shows a single cycle Pass-Thru read access
(Add-On write) using PTADR#. The Add-On reads
data from a source on the Add-On and writes it to the
APTD register.
PCI address information is stored in the S5335 Pass-Thru Address Register. The PCI cycle is recognized as an
access to Pass-Thru region 1. PTATN# is asserted by the S5335 to indicate a Pass-Thru access is occurring.
Clock 0:
Clock 1:
Pass-Thru status signals indicate what action is required by Add-On logic. Pass-Thru status outputs are valid
when PTATN# is active and are sampled by the Add-On at the rising edge of clock 1.
PTBURST# Deasserted. The access has a single data phase. PTNUM[1:0] 01. Indicates the PCI access was
to Pass-Thru region 1.
PTWR
Deasserted. The Pass-Thru access is a read.
PTBE[3:0]# 0h. Indicate the Pass-Thru access is 32-bits.
The PTADR# input is asserted to read the Pass-Thru Address Register. The byte enable, address, and SELECT#
inputs are changed during this clock to select the Pass-Thru Data Register during clock cycle 3.
This clock is required to avoid contention on the DQ bus. Time must be allowed after PTADR# is deasserted for
the DQ outputs to float before Add-On logic attempts to write to the Pass-Thru Data Register.
Clock 2:
Clock 3:
SELECT#, byte enables, and the address inputs remain valid to write the Pass-Thru Data Register at offset 2Ch.
If WR# is asserted at the rising edge of clock 3, data on the DQ bus is latched into APTD.
If PTRDY# is asserted at the rising edge of clock 3, PTATN# is immediately deasserted and the Pass-Thru
access is completed at clock 4.
If Add-On logic requires more time to write the Pass-Thru data register (slower memory or peripherals), PTRDY#
can be delayed, extending the cycle. PTRDY# asserted at the rising edge of clock 4 causes PTATN# to be imme-
diately deasserted and the Pass-Thru access is completed at clock 5.
Clock 4:
Clock 5:
PTATN# and PTBURST# deasserted at the rising edge of clock 5 indicates the Pass-Thru access is complete.
The S5335 can accept new Pass-Thru accesses from the PCI bus at clock 6.
Pass-Thru Burst Writes
Figure 86 shows a 6 data phase Pass-Thru burst write
(Add-On read). In this case, the Add-On asserts
PTADR# and then reads multiple data phases from the
S5335. This works well for Add-On logic which sup-
ports burst cycles. If the Add-On logic does not
support burst accesses, PTADR# may be pulsed
before each data phase. The S5335 automatically
increments the address in the APTA register during
PCI burst cycles. In this example PTRDY# is always
asserted, indicating Add-On logic is capable of accept-
ing data at a rate of one DWORD per clock cycle.
A Pass-Thru burst write operation occurs when a PCI
initiator writes multiple values to a Pass-Thru region. A
PCI burst cycle consists of an address phase and mul-
tiple data phases. During the address phase of the
PCI transfer, the S5335 stores the PCI address into
the Pass-Thru Address Register (APTA). If the S5335
determines that the address is within one of its defined
Pass-Thru regions, it captures the PCI data into the
Pass-Thru Data Register (APTD). After the Add-On
completes each read from the Pass-Thru data register
(asserts PTRDY#), the next data phase is initiated.
AMCC Confidential and Proprietary
DS1657 147