欢迎访问ic37.com |
会员登录 免费注册
发布采购

D85C220-80 参数 Datasheet PDF下载

D85C220-80图片预览
型号: D85C220-80
PDF下载: 下载PDF文件 查看货源
内容描述: 经典EPLD中 [Classic EPLDs]
分类和应用: 可编程逻辑输入元件时钟
文件页数/大小: 16 页 / 400 K
品牌: ALTERA [ ALTERA CORPORATION ]
 浏览型号D85C220-80的Datasheet PDF文件第8页浏览型号D85C220-80的Datasheet PDF文件第9页浏览型号D85C220-80的Datasheet PDF文件第10页浏览型号D85C220-80的Datasheet PDF文件第11页浏览型号D85C220-80的Datasheet PDF文件第13页浏览型号D85C220-80的Datasheet PDF文件第14页浏览型号D85C220-80的Datasheet PDF文件第15页浏览型号D85C220-80的Datasheet PDF文件第16页  
EP220 & EP224 Classic EPLDs  
I
Supply Current: EP220-7A & EP224-7A  
Note (5)  
CC  
Symbol  
Parameter  
Conditions  
Min  
Min  
Max  
Unit  
ICC3  
VCC supply current  
fIN = 25 MHz, Note (9)  
fIN = 100 MHz, Note (9)  
90  
mA  
mA  
115  
I
Supply Current: EP220-10A, EP224-10A, EP220-12 & EP224-12  
Note (5)  
CC  
Symbol  
Parameter  
Conditions  
Max  
Unit  
ICC1  
ICC2  
VCC supply current (non-turbo)  
VCC supply current (non-turbo)  
Standby mode, Note (9)  
500  
5
µA  
VCC = Max., VIN = VCC or GND,  
mA  
no load, fIN = 1 MHz, Notes (9), (10)  
ICC3  
VCC supply current (turbo, active)  
fIN = 15 MHz, Note (9)  
fIN = 80 MHz, Note (9)  
50  
60  
mA  
mA  
I
Supply Current: EP220-7, EP224-7, EP220-10 & EP224-10  
Note (5)  
CC  
Symbol  
Parameter  
Conditions  
Min  
Max  
Unit  
ICC1  
VCC supply current (standby)  
fIN = 25 MHz, Note (9)  
fIN = 74 MHz, Note (9)  
fIN = 25 MHz, Note (9)  
fIN = 74 MHz, Note (9)  
90  
µA  
mA  
mA  
mA  
105  
115  
135  
ICC3  
VCC supply current (active)  
Notes to tables:  
(1) See Operating Requirements for Altera Devices in the Altera 1995 Data Book.  
(2) Voltage with respect to ground.  
(3) Minimum DC input is –0.5 V. During transitions, the inputs may undershoot to –2.0 V or overshoot to 7.0 V for  
periods less than 20 ns under no-load conditions.  
(4) Under bias. Extended temperature versions are also available.  
(5) Operating conditions:  
T
T
A = 0° C to 70° C, VCC = 5.0 V ± 5% for commercial use.  
A = –40° C to 85° C, VCC = 5.0 V ± 10% for industrial use.  
(6) Absolute values with respect to device GND; all over- and undershoots due to system or tester noise are included.  
(7) For -7A, -10A, -12 speed grades for EP220 and EP224 devices: maximum DC IOL (all 8 outputs) = 64 mA.  
For -7, -10 speed grades for EP220 and EP224 devices: test 1 output at a time; test duration should not exceed 1 s.  
(8) These values are measured during initial characterization. VCC = Max., VIN = VCC or GND.  
(9) Measured with a device programmed as an 8-bit counter.  
(10) When the Turbo Bit is not set (non-turbo mode), an EP220 or EP224 device enters standby mode if no logic  
transitions occur for approximately 75 ns after the last transition.  
12  
Altera Corporation