IAM-91563-TR1 参数 Datasheet PDF下载

IAM-91563 Absolute Maximum Ratings

Symbol

V

d

V

RF,

V

LO

P

in

T

ch

T

STG

Parameter

Device Voltage, RF output to ground

RF voltage or LO voltage to ground

CW RF Input Power

Channel Temperature

Storage Temperature

Absolute

Units Maximum

[1]

V

V

dBm

°C

°C

6.0

+0.5, -1.0

+13

150

-65 to 150

Thermal Resistance

[2]

:

θ

ch-c

= 310°C/W

Notes:

1. Permanent damage may occur if

any of these limits are exceeded.

2. T

C

= 25°C (T

C

is defined to be the

temperature at the package pins

where contact is made to the

circuit board).

IAM-91563 Electrical Specifications,

T

C

= 25°C, V

d

= 3 V

Symbol

G

test

NF

test

I

d

NF

Parameters and Test Conditions

Gain in test circuit

[1]

Noise Figure in test circuit

[1]

Device Current

Noise Figure (RF & IF with external matching,

IF=250 MHz, LO power=-5 dBm)

f = 0.9 GHz

f = 1.9 GHz

f = 2.4 GHz

f = 4.0 GHz

f = 6.0 GHz

f = 0.9 GHz

f = 1.9 GHz

f = 2.4 GHz

f = 4.0 GHz

f = 6.0 GHz

f = 0.9 GHz

f = 1.9 GHz

f = 2.4 GHz

f = 4.0 GHz

f = 6.0 GHz

RF=1890 GHz, IF=250 MHz

RF=1890 GHz, IF=250 MHz

Units Min. Typ. Max.

Std Dev

[2]

dB

dB

mA

dB

6.0

4.0

9.0

8.5

9.0

7.0

8.5

11.0

16.5

18.0

11.0

9.0

7.7

4.6

1.7

-6.7

-8.0

-8.7

-15.0

-17.8

-1.7

-9.4

-3.7

-6.0

0

18

2

4

11.0

12.0

0.5

G

c

Conversion gain (RF and IF with external matching,

IF=250 MHz, LO power=-5 dBm)

dB

1.5

P

1 dB

Output power @ 1 dB compression (RF and IF with

external matching, IF=250 MHz, LO power =-5 dBm)

dBm

1.3

RL

RF

RL

LO

RL

IF

IP

3

IP

3

RF port return loss

LO port return loss

IF port return loss

Input Third Order Intercept Point

I

d

= 9.0 mA, LO power = -5 dBm

Input Third Order Intercept Point

I

d

= 15 mA, LO power = -2 dBm

f = 0.5 - 6.0 GHz

f = 0.5 - 6.0 GHz

f = 50 - 700 MHz

RF = 1.9 GHz, IF = 250 MHz

RF = 1.9 GHz, IF = 250 MHz

RF = 1.9 GHz

dB

dB

dB

dBm

dBm

dB

dB

dB

0.2

0.3

0.2

1.3

1.1

ISOL

L-R

LO-RF Isolation

ISOL

R-I

RF-IF Isolation (No Match)

ISOL

L-I

LO-IF Isolation (No Match)

Notes:

1. Guaranteed specifications are 100% tested in the circuit in Figure 18 in the Applications Information section.

2. Standard deviation number is based on measurement of at least 500 parts from three non-consecutive wafer lots during

the initial characterization of this product, and is intended to be used as an estimate for distribution of the typical

specification.

7-136