Notes:
1. Derate linearly above 70°C free-air
temperature at a rate of 0.3 mA/°C.
2. Maximum pulse width = 10
µs,
maximum duty cycle = 0.2%. This
value is intended to allow for
component tolerances for designs
with I
O
peak minimum = 0.5 A. See
Applications section for additional
details on limiting I
OH
peak.
3. Derate linearly above 70°C free-air
temperature at a rate of 4.8 mW/°C.
4. Derate linearly above 70°C free-air
temperature at a rate of 5.4 mW/°C.
The maximum LED junction tempera-
ture should not exceed 125°C.
5. Maximum pulse width = 50
µs,
maximum duty cycle = 0.5%.
6. In this test V is measured with a dc
OH
load current. When driving capacitive
loads V
OH
will approach V
CC
as I
OH
approaches zero amps.
7. Maximum pulse width = 1 ms,
maximum duty cycle = 20%.
8. In accordance with UL1577, each
optocoupler is proof tested by
applying an insulation test voltage
≥
3000 Vrms for 1 second (leakage
detection current limit, I
I-O
≤
5
µA).
This test is performed before the
100% production test for partial
discharge (method b) shown in the
VDE 0884 Insulation Characteristics
Table, if applicable.
9. Device considered a two-terminal
device: pins 1, 2, 3, and 4 shorted
together and pins 5, 6, 7, and 8
shorted together.
10. The difference between t
PHL
and t
PLH
between any two HCPL-3150 parts
11.
12.
13.
14.
15.
under the same test condition.
Pins 1 and 4 need to be connected to
LED common.
Common mode transient immunity in
the high state is the maximum
tolerable |dV
CM
/dt| of the common
mode pulse, V
CM
, to assure that the
output will remain in the high state
(i.e., V
O
> 15.0 V).
Common mode transient immunity in
a low state is the maximum tolerable
|dV
CM
/dt| of the common mode
pulse, V
CM
, to assure that the output
will remain in a low state (i.e.,
V
O
< 1.0 V).
This load condition approximates the
gate load of a 1200 V/25 A IGBT.
Pulse Width Distortion (PWD) is
defined as |t
PHL
-t
PLH
| for any given
device.
(V
OH
- V
CC
) – HIGH OUTPUT VOLTAGE DROP – V
0
I
OH
– OUTPUT HIGH CURRENT – A
(V
OH
- V
CC
) – OUTPUT HIGH VOLTAGE DROP – V
-1
I
F
= 7 to 16 mA
I
OUT
= -100 mA
V
CC
= 15 to 30 V
V
EE
= 0 V
0.50
I
F
= 7 to 16 mA
V
OUT
= V
CC
- 4 V
V
CC
= 15 to 30 V
V
EE
= 0 V
-1
100 °C
25 °C
-40 °C
0.45
-2
0.40
-3
-2
0.35
-4
I
F
= 7 to 16 mA
V
CC
= 15 to 30 V
V
EE
= 0 V
0
0.2
0.4
0.6
0.8
1.0
-3
0.30
0.25
-40 -20
-5
-6
-4
-40 -20
0
20
40
60
80
100
0
20
40
60
80
100
T
A
– TEMPERATURE – °C
T
A
– TEMPERATURE – °C
I
OH
– OUTPUT HIGH CURRENT – A
Figure 1. V
OH
vs. Temperature.
Figure 2. I
OH
vs. Temperature.
Figure 3. V
OH
vs. I
OH
.
1.0
V
OL
– OUTPUT LOW VOLTAGE – V
1.0
I
OL
– OUTPUT LOW CURRENT – A
V
OL
– OUTPUT LOW VOLTAGE – V
5
V
F(OFF)
= -3.0 to 0.8 V
V
CC
= 15 to 30 V
4 V
EE
= 0 V
3
0.8
V
F(OFF)
= -3.0 to 0.8 V
I
OUT
= 100 mA
V
CC
= 15 to 30 V
V
EE
= 0 V
0.8
0.6
0.6
0.4
0.4
V
F(OFF)
= -3.0 to 0.8 V
V
OUT
= 2.5 V
V
CC
= 15 to 30 V
V
EE
= 0 V
0
20
40
60
80
100
2
0.2
0
-40 -20
0.2
1
0
0
20
40
60
80
100
0
-40 -20
100 °C
25 °C
-40 °C
0
0.2
0.4
0.6
0.8
1.0
I
OL
– OUTPUT LOW CURRENT – A
T
A
– TEMPERATURE – °C
T
A
– TEMPERATURE – °C
Figure 4. V
OL
vs. Temperature.
Figure 5. I
OL
vs. Temperature.
Figure 6. V
OL
vs. I
OL
.
1-203
AGILENT [ AGILENT TECHNOLOGIES, LTD. ]
