Package Characteristics
Parameter
Symbol Min.
Input-Output Momentary
V
ISO
2500
Withstand Voltage
Resistance
R
I-O
(Input-Output)
Capacitance
C
I-O
(Input-Output)
Input Capacitance
C
I
Input IC Junction-to-Case
θ
jci
Thermal Resistance
Output IC Junction-to-Case
θ
jco
Thermal Resistance
Package Power Dissipation
P
PD
Notes:
1. Absolute Maximum ambient operating
temperature means the device will not
be damaged if operated under these
conditions. It does not guarantee
functionality.
2. The LED is ON when V
I
is low and OFF
when V
I
is high.
3. t
PHL
propagation delay is measured
from the 50% level on the falling edge
of the V
I
signal to the 50% level of the
falling edge of the V
O
signal. t
PLH
propagation delay is measured from
the 50% level on the rising edge of the
V
I
signal to the 50% level of the rising
edge of the V
O
signal.
4. Mimimum Pulse Width is the shortest
pulse width at which 10% maximum,
Pulse Width Distortion can be guaran-
teed. Maximum Data Rate is the
inverse of Minimum Pulse Width.
Operating the HCPL-0710 at data rates
above 12.5 MBd is possible provided
PWD and data dependent jitter
increases and relaxed noise margins
Typ.
Max.
Units
Vrms
Ω
pF
10
12
0.6
3.0
160
135
150
Test Conditions
Fig.
RH
≤
50%, t = 1 min.,
T
A
= 25°C
V
I-O
= 500 Vdc
f = 1 MHz
Note
9, 10,
11
9
12
°C/W
Thermocouple
located at center
underside of
package
mW
are tolerable within the application.
For instance, if the maximum
allowable variation of bit width is 30%,
the maximum data rate becomes 37.5
MBd. Please note that HCPL-0710
performance above 12.5 MBd is not
guaranteed by Hewlett-Packard.
5. PWD is defined as |t
PHL
- t
PLH
|.
%PWD (percent pulse width distortion)
is equal to the PWD divided by pulse
width.
6. t
PSK
is equal to the magnitude of the
worst case difference in t
PHL
and/or
t
PLH
that will be seen between units at
any given temperature within the
recommended operating conditions.
7. CM
H
is the maximum common mode
voltage slew rate that can be sustained
while maintaining V
O
> 0.8 V
DD2
. CM
L
is the maximum common mode voltage
slew rate that can be sustained while
maintaining V
O
< 0.8 V. The common
mode voltage slew rates apply to both
rising and falling common mode
voltage edges.
2.2
8. Unloaded dynamic power dissipation is
calculated as follows: C
PD
* V
DD2
* f +
I
DD
* V
DD
, where f is switching
frequency in MHz.
9. Device considered a two-terminal
device: pins 1, 2, 3, and 4 shorted
together and pins 5, 6, 7, and 8
shorted together.
10. In accordance with UL1577, each
optocoupler is proof tested by
applying an insulation test voltage
≥
3000 V
RMS
for 1 second (leakage
detection current limit, I
I-O
≤
5
µA).
11. The Input-Output Momentary With-
stand Voltage is a dielectric voltage
rating that should not be interpreted as
an input-output continuous voltage
rating. For the continuous voltage
rating refer to your equipment level
safety specification or HP Application
Note 1074 entitled “Optocoupler
Input-Output Endurance Voltage.”
12. C
I
is the capacitance measured at pin
2 (V
I
).
5
4
V
O
(V)
T
PLH
, T
PHL
(ns)
0 °C
25 °C
85 °C
V
ITH
(V)
2.1
2.0
1.9
1.8
1.7
1.6
4.5
0 °C
25 °C
85 °C
29
27
25
23
21
19
17
T
PHL
T
PLH
3
2
1
0
0
1
2
V
I
(V)
3
4
5
4.75
5
V
DD1
(V)
5.25
5.5
15
0
10
20 30
40
50
60 70
80
T
A
(C)
Figure 1. Typical Output Voltage vs.
Input Voltage.
Figure 2. Typical Input Voltage
Switching Threshold vs. Input Supply
Voltage.
Figure 3. Typical Propagation Delays
vs. Temperature.
AGILENT [ AGILENT TECHNOLOGIES, LTD. ]
