Data Sheet
June 1999
ORCA Series 3C and 3T FPGAs
5 V Tolerant I/O
Programmable Input/Output Cells
(continued)
The I/O on the OR3Txxx Series devices allow intercon-
nection to both 3.3 V and 5 V devices (selectable on a
per-pin basis).
Table 9. PIO Options
Input
Input Level
Option
The OR3Txxx devices will drive the pin to the 3.3 V lev-
els when the output buffer is enabled. If the other
device being driven by the OR3Txxx device has TTL-
compatible inputs, then the device will not dissipate
much input buffer power. This is because the OR3Txxx
output is being driven to a higher level than the TTL
level required. If the other device has a CMOS-compat-
ible input, the amount of input buffer power will also be
small. Both of these power values are dependent upon
the input buffer characteristics of the other device when
driven at the OR3Txxx output buffer voltage levels.
TTL, OR3Cxx only
CMOS, OR3Cxx or OR3Txxx
3.3 V PCI Compliant, OR3Txxx
5 V PCI Compliant, OR3Txxx
Input Speed
Float Value
Fast, Delayed
Pull-up, Pull-down, None
Register Mode
Latch, FF, Fast Zero Hold FF,
None (direct input)
Clock Sense
Inverted, Noninverted
Input Selection
Input 1, Input 2, Clock Input
The OR3Txxx device has internal programmable pull-
ups on the I/O buffers. These pull-up voltages are
always referenced to VDD and are always sufficient to
pull the input buffer of the OR3Txxx device to a high
state. The pin on the OR3Txxx device will be at a level
1.0 V below VDD (minimum of 2.0 V with a minimum
VDD of 3.0 V). This voltage is sufficient to pull the exter-
nal pin up to a 3.3 V CMOS high input level (1.8 V, min)
or a TTL high input level (2.0 V, min) in a 5 V tolerant
system. Therefore, in a 5 V tolerant system using 5 V
CMOS parts, care must be taken to evaluate the use of
these pull-ups to pull the pin of the OR3Txxx device to
a typical 5 V CMOS high input level (2.2 V, min).
Output
Option
Output Drive
Current
12 mA/6 mA or 6 mA/3 mA
Output Function
Output Speed
Output Source
Output Sense
3-State Sense
FF Clocking
Normal, Fast Open Drain
Fast, Slewlim, Sinklim
FF Direct-out, General Routing
Active-high, Active-low
Active-high, Active-low (3-state)
ExpressCLK, System Clock
Inverted, Noninverted
Clock Sense
Logic Options
See Table 10.
PCI Compliant I/O
I/O Controls
Option
Clock Enable
Active-high, Active-low,
Always Enabled
The I/O on the OR3Txxx Series devices allows compli-
ance with PCI Local Bus (Rev. 2.2) 5 V and 3.3 V sig-
naling environments. The signaling environment used
for each input buffer can be selected on a per-pin basis.
The selection provides the appropriate I/O clamping
diodes for PCI compliance. Choosing an IBT input
buffer will provide PCI compliance in OR3Txxx devices.
OR3Cxx devices have PCI Local Bus compliant I/Os for
5 V signaling.
Set/Reset Level
Set/Reset Type
Active-high, Active-low,
No Local Reset
Synchronous, Asynchronous
Set/Reset Priority CE over LSR, LSR over CE
GSR Control Enable GSR, Disable GSR
Lucent Technologies Inc.
37
AGERE [ AGERE SYSTEMS ]
