欢迎访问ic37.com |
会员登录 免费注册
发布采购

L8576B 参数 Datasheet PDF下载

L8576B图片预览
型号: L8576B
PDF下载: 下载PDF文件 查看货源
内容描述: 双振铃SLIC [Dual Ringing SLIC]
分类和应用:
文件页数/大小: 26 页 / 564 K
品牌: AGERE [ AGERE SYSTEMS ]
 浏览型号L8576B的Datasheet PDF文件第6页浏览型号L8576B的Datasheet PDF文件第7页浏览型号L8576B的Datasheet PDF文件第8页浏览型号L8576B的Datasheet PDF文件第9页浏览型号L8576B的Datasheet PDF文件第11页浏览型号L8576B的Datasheet PDF文件第12页浏览型号L8576B的Datasheet PDF文件第13页浏览型号L8576B的Datasheet PDF文件第14页  
Data Sheet  
May 2001  
L8576B Dual Ringing SLIC  
Electrical Characteristics  
Generally, minimum and maximum values are testing requirements. However, some parameters may not be tested  
in production because they are guaranteed by design and device characterization. Typical values reflect the design  
center or nominal value of the parameter; they are for information only and are not a requirement. Minimum and  
maximum values apply across the entire temperature range (0 °C to 70 °C) and entire battery range (to –72 V).  
Unless otherwise specified, typical values are defined as 20 °C, VCC = 5.0 V, VBAT = –68.5 V. Positive currents flow  
into the device.  
Table 3. Operating Conditions and Powering  
Parameter  
Min  
Typ  
Max  
Unit  
Temperature Range  
0
70  
951  
°C  
Humidity Range  
5
%RH  
Supply Voltages:  
VCC  
VBAT  
4.75  
–242  
5.0  
–65  
5.25  
–72  
V
V
Loop Closure Threshold—Detection Range  
ac Termination Impedance Programming Range  
On- and Off-hook 2-wire Signal Level  
9.5  
300  
12  
14.5  
10003  
mA  
600  
3.14  
dBm  
Power Supply—Powerup, No Loop Current (per section):  
ICC  
4.5  
3.0  
230  
5.5  
4.0  
290  
mA  
mA  
mW  
IBAT (VBAT = –65 V)  
Total power (one channel, VBAT = –65 V)  
Power-supply Rejection (See Figures 6 and 7.):  
VCC (1 kHz)  
35  
45  
dB  
dB  
VBAT (500 Hz—3 kHz)  
Thermal4:  
Thermal Resistance (still air) Tj  
Operating Tj  
Thermal Shutdown Temperature  
47  
160  
150  
°C/W  
°C  
°C  
1. Noncondensing.  
2. The L8576B will operate below –24 V; –24 V is used for production test.  
3. The termination impedance can be programmed up to 1200 ; 1000 are used for production test.  
4. This parameter is not tested in production. It is guaranteed by design and device characterization.  
Table 4. Ring Trip Detector1  
Parameter2  
Min Typ Max  
Unit  
Ringing Source:  
Frequency (ƒ) RRNG = 28.7 kΩ, RTTH = 52.3 kΩ  
Frequency (ƒ) Contact Agere for Specific Component Values  
17  
20  
20  
23  
50  
Hz  
Hz  
C-message Weighted Noise (900 )  
90  
40  
dBrnC  
Vrms  
REN Load (1386 + 40 µF) with Loop Resistance = 30 Ω, RPT = 30 Ω, RPR = 30 Ω  
Detection Interval:  
20 Hz  
200  
150  
ms  
ms  
25 Hz  
1. This table is provided for information purposes only.  
2. These parameters are not tested in production.  
10  
Agere Systems Inc.