ADV7125
PIN CONFIGURATION AND FUNCTION DESCRIPTIONS
48
47
46
45
44
43
42
41
40
39
38
37
R7
R6
R5
R4
R3
R2
R1
R0
GND
GND
PSAVE
R
SET
GND
GND
1
2
PIN 1
INDICATOR
NOTES
1. THE LFCSP_VQ HAS AN EXPOSED PADDLE THAT MUST BE
CONNECTED TO GND.
Table 6. Pin Function Descriptions
Pin Number
1, 2, 14, 15, 25,
26, 39, 40
3 to 10, 16 to
23, 41 to 48
11
Mnemonic
GND
G0 to G7,
B0 to B7,
R0 to R7
BLANK
Description
Ground. All GND pins must be connected.
Red, Green, and Blue Pixel Data Inputs (TTL Compatible). Pixel data is latched on the rising edge of
CLOCK. R0, G0, and B0 are the least significant data bits. Unused pixel data inputs should be
connected to either the regular printed circuit board (PCB) power or ground plane.
Composite Blank Control Input (TTL Compatible). A Logic 0 on this control input drives the analog
outputs, IOR, IOB, and IOG, to the blanking level. The BLANK signal is latched on the rising edge of
CLOCK. While BLANK is a Logic 0, the R0 to R7, G0 to G7, and B0 to B7 pixel inputs are ignored.
Composite Sync Control Input (TTL Compatible). A Logic 0 on the SYNC input switches off a
40 IRE current source. This is internally connected to the IOG analog output. SYNC does not override
any other control or data input; therefore, it should only be asserted during the blanking interval.
SYNC is latched on the rising edge of CLOCK. If sync information is not required on the green channel,
the SYNC input should be tied to Logic 0.
Analog Power Supply (5 V ± 5%). All V
AA
pins on the ADV7125 must be connected.
Clock Input (TTL Compatible). The rising edge of CLOCK latches the R0 to R7, G0 to G7, B0 to B7, SYNC,
and BLANK pixel and control inputs. It is typically the pixel clock rate of the video system. CLOCK
should be driven by a dedicated TTL buffer.
Differential Red, Green, and Blue Current Outputs (High Impedance Current Sources). These RGB video
outputs are specified to directly drive RS-343A and RS-170 video levels into a doubly terminated 75 Ω
load. If the complementary outputs are not required, these outputs should be tied to ground.
Red, Green, and Blue Current Outputs. These high impedance current sources are capable of directly
driving a doubly terminated 75 Ω coaxial cable. All three current outputs should have similar output
loads whether or not they are all being used.
Compensation Pin. This is a compensation pin for the internal reference amplifier. A 0.1 μF ceramic
capacitor must be connected between COMP and V
AA
.
Voltage Reference Input for DACs or Voltage Reference Output (1.235 V).
12
SYNC
13, 29, 30
24
V
AA
CLOCK
33, 31, 27
IOR, IOG, IOB
34, 32, 28
IOR, IOG, IOB
35
36
COMP
V
REF
V
AA
GND
GND
B0
B1
B2
B3
B4
B5
B6
B7
CLOCK
13
14
15
16
17
18
19
20
21
22
23
24
Figure 3. Pin Configuration
Rev. C | Page 8 of 16
03097-003
G0 3
G1 4
G2 5
G3 6
G4 7
G5 8
G6 9
G7 10
BLANK 11
SYNC 12
ADV7125
TOP VIEW
(Not to Scale)
36
35
34
33
32
31
30
29
28
27
26
25
V
REF
COMP
IOR
IOR
IOG
IOG
V
AA
V
AA
IOB
IOB
GND
GND
AD [ ANALOG DEVICES ]
