ADuM5401/ADuM5402/ADuM5403/ADuM5404
SPECIFICATIONS
Data Sheet
ELECTRICAL CHARACTERISTICS—5 V PRIMARY INPUT SUPPLY/5 V SECONDARY ISOLATED SUPPLY
Typical specifications are at T
A
= 25°C, V
DD1
= V
SEL
= V
ISO
= 5 V. Minimum/maximum specifications apply over the entire recommended
operation range which is 4.5 V ≤ V
DD1
, V
SEL
, V
ISO
≤ 5.5 V; and −40°C ≤ T
A
≤ +105°C, unless otherwise noted. Switching specifications are
tested with C
L
= 15 pF and CMOS signal levels, unless otherwise noted.
Table 2. DC-to-DC Converter Static Specifications
Parameter
DC-TO-DC CONVERTER SUPPLY
Setpoint
Line Regulation
Load Regulation
Output Ripple
Output Noise
Switching Frequency
PWM Frequency
Output Supply Current
Efficiency at I
ISO (MAX)
I
DD1
, No V
ISO
Load
I
DD1
, Full V
ISO
Load
Symbol
V
ISO
V
ISO (LINE)
V
ISO (LOAD)
V
ISO (RIP)
V
ISO (NOISE)
f
OSC
f
PWM
I
ISO (MAX)
I
DD1 (Q)
I
DD1 (MAX)
Min
4.7
Typ
5.0
1
1
75
200
180
625
34
19
290
Max
5.4
5
Unit
V
mV/V
%
mV p-p
mV p-p
MHz
kHz
mA
%
mA
mA
Test Conditions/Comments
I
ISO
= 0 mA
I
ISO
= 50 mA, V
DD1
= 4.5 V to 5.5 V
I
ISO
= 10 mA to 90 mA
20 MHz bandwidth, C
BO
= 0.1 µF||10 µF, I
ISO
= 90 mA
C
BO
= 0.1 µF||10 µF, I
ISO
= 90 mA
100
30
V
ISO
> 4.5 V
I
ISO
= 100 mA
Table 3. DC-to-DC Converter Dynamic Specifications
Parameter
SUPPLY CURRENT
Input
Available to Load
Symbol
I
DD1
19
19
19
19
I
ISO (LOAD)
100
100
100
100
87
85
83
81
mA
mA
mA
mA
68
71
75
78
mA
mA
mA
mA
No V
ISO
load
No V
ISO
load
No V
ISO
load
No V
ISO
load
1 Mbps—A Grade, C Grade
Min
Typ
Max
25 Mbps—C Grade
Min
Typ
Max
Unit
Test Conditions/Comments
Table 4. Switching Specifications
Parameter
SWITCHING SPECIFICATIONS
Data Rate
Propagation Delay
Pulse Width Distortion
Change vs. Temperature
Pulse Width
Propagation Delay Skew
Channel Matching
Codirectional
Opposing Directional
1
7
Symbol
Min
A Grade
Typ
Max
1
100
40
Min
C Grade
Typ
Max
25
60
6
Unit
Mbps
ns
ns
ps/°C
ns
ns
ns
ns
Test Conditions/Comments
Within PWD limit
50% input to 50% output
|t
PLH
− t
PHL
|
Within PWD limit
Between any two units
t
PHL
, t
PLH
PWD
PW
t
PSK
t
PSKCD
t
PSKOD
1000
55
45
5
40
50
50
50
15
6
15
Codirectional channel matching is the absolute value of the difference in propagation delays between any two channels with inputs on the same side of the isolation
barrier.
2
Opposing directional channel matching is the absolute value of the difference in propagation delays between any two channels with inputs on opposing sides of the
isolation barrier.
Rev. C | Page 4 of 28
AD [ ANALOG DEVICES ]
