ADuM1200/ADuM1201
Parameter
Symbol Min
Typ Max
Unit
Test Conditions
ADuM120xBR
Minimum Pulse Width2
Maximum Data Rate3
Propagation Delay4
Pulse-Width Distortion, |tPLH −tPHL
Change Versus Temperature
Propagation Delay Skew5
PW
100
ns
Mbps
ns
ns
ps/°C
ns
CL = 15 pF, CMOS signal levels
CL = 15 pF, CMOS signal levels
CL = 15 pF, CMOS signal levels
CL = 15 pF, CMOS signal levels
CL = 15 pF, CMOS signal levels
CL = 15 pF, CMOS signal levels
CL = 15 pF, CMOS signal levels
10
tPHL, tPLH 20
PWD
60
3
4
|
5
tPSK
tPSKCD
22
3
Channel-to-Channel Matching,
Codirectional Channels6
ns
Channel-to-Channel Matching,
tPSKOD
tR/tF
22
ns
ns
CL = 15 pF, CMOS signal levels
CL = 15 pF, CMOS signal levels
Opposing Directional Channels6
Output Rise/Fall Time (10% to 90%)
ADuM120xCR
3.0
Minimum Pulse Width2
PW
20
50
40
ns
Mbps
ns
ns
ps/°C
ns
CL = 15 pF, CMOS signal levels
CL = 15 pF, CMOS signal levels
CL = 15 pF, CMOS signal levels
CL = 15 pF, CMOS signal levels
CL = 15 pF, CMOS signal levels
CL = 15 pF, CMOS signal levels
CL = 15 pF, CMOS signal levels
Maximum Data Rate3
25
tPHL, tPLH 20
PWD
Propagation Delay4
55
3
4
Pulse-Width Distortion, |tPLH − tPHL
Change Versus Temperature
Propagation Delay Skew5
Channel-to-Channel Matching,
Codirectional Channels6
|
5
tPSK
tPSKCD
16
3
ns
Channel-to-Channel Matching,
tPSKOD
tR/tF
16
ns
ns
CL = 15 pF, CMOS signal levels
CL = 15 pF, CMOS signal levels
Opposing Directional Channels6
Output Rise/Fall Time (10% to 90%)
For All Models
3.0
Common Mode Transient Immunity
at Logic High Output7
Common Mode Transient Immunity
at Logic Low Output7
|CMH|
|CML|
25
25
35
35
kV/µs
kV/µs
VIx = VDD1, VDD2, VCM = 1000 V,
transient magnitude = 800 V
VIx = 0 V, VCM = 1000 V,
transient magnitude = 800 V
Refresh Rate
fr
1.1
0.10
0.03
Mbps
mA/Mbps
mA/Mbps
Input Dynamic Supply Current, per Channel8
IDDI (D)
Output Dynamic Supply Current, per Channel8 IDDO (D)
1 The supply current values for both channels are combined when running at identical data rates. Output supply current values are specified with no output load
present. The supply current associated with an individual channel operating at a given data rate may be calculated as described in the Power Consumption section. See
Figure 6 through Figure 8 for information on per-channel supply current as a function of data rate for unloaded and loaded conditions. See Figure 9 through Figure 11
for total IDD1 and IDD2 supply currents as a function of data rate for ADuM1200 and ADuM1201 channel configurations.
2 The minimum pulse width is the shortest pulse width at which the specified pulse-width distortion is guaranteed.
3 The maximum data rate is the fastest data rate at which the specified pulse-width distortion is guaranteed.
4 tPHL propagation delay is measured from the 50% level of the falling edge of the VIx signal to the 50% level of the falling edge of the VOx signal. tPLH propagation delay is
measured from the 50% level of the rising edge of the VIx signal to the 50% level of the rising edge of the VOx signal.
5 tPSK is the magnitude of the worst-case difference in tPHL and/or tPLH that is measured between units at the same operating temperature, supply voltages, and output
load within the recommended operating conditions.
6 Codirectional channel-to-channel matching is the absolute value of the difference in propagation delays between any two channels with inputs on the same side of
the isolation barrier. Opposing directional channel-to-channel matching is the absolute value of the difference in propagation delays between any two channels with
inputs on opposing sides of the isolation barrier.
7 CMH is the maximum common-mode voltage slew rate that can be sustained while maintaining VO > 0.8 VDD2. CML is the maximum common-mode voltage slew rate
that can be sustained while maintaining VO < 0.8 V. The common-mode voltage slew rates apply to both rising and falling common-mode voltage edges. The transient
magnitude is the range over which the common mode is slewed.
8 Dynamic supply current is the incremental amount of supply current required for a 1 Mbps increase in the signal data rate. See Figure 6 through Figure 8 for
information on per-channel supply current for unloaded and loaded conditions. See the Power Consumption section for guidance on calculating per-channel supply
current for a given data rate.
Rev. B | Page 6 of 20
ADI [ ADI ]
