ADG417
ABSOLUTE MAXIMUM RATINGS
1
(T
A
= +25°C unless otherwise noted)
V
DD
to V
SS
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . +44 V
V
DD
to GND . . . . . . . . . . . . . . . . . . . . . . . . . . –0.3 V to +25 V
V
SS
to GND . . . . . . . . . . . . . . . . . . . . . . . . . . +0.3 V to –25 V
V
L
to GND . . . . . . . . . . . . . . . . . . . . . . –0.3 V to V
DD
+ 0.3 V
Analog, Digital Inputs
2
. . . . . . . . . . . . . V
SS
– 2 V to V
DD
+2 V
or 30 mA, Whichever Occurs First
Continuous Current, S or D . . . . . . . . . . . . . . . . . . . . . 30 mA
Peak Current, S or D . . . . . . . . . . . . . . . . . . . . . . . . . 100 mA
(Pulsed at 1 ms, 10% Duty Cycle Max)
Operating Temperature Range
Industrial (B Version) . . . . . . . . . . . . . . . . . –40°C to +85°C
Extended (T Version) . . . . . . . . . . . . . . . . –55°C to +125°C
Storage Temperature Range . . . . . . . . . . . . . –65°C to +150°C
Junction Temperature . . . . . . . . . . . . . . . . . . . . . . . . . . 150°C
Plastic Package, Power Dissipation . . . . . . . . . . . . . . . 400 mW
θ
JA
, Thermal Impedance . . . . . . . . . . . . . . . . . . . . 100°C/W
Lead Temperature, Soldering (10 sec) . . . . . . . . . . . +260°C
SOIC Package, Power Dissipation . . . . . . . . . . . . . . . . 400 mW
θ
JA
, Thermal Impedance . . . . . . . . . . . . . . . . . . . . 155°C/W
Lead Temperature, Soldering
Vapor Phase (60 sec). . . . . . . . . . . . . . . . . . . . . . . +215°C
Infrared (15 sec) . . . . . . . . . . . . . . . . . . . . . . . . . . +220°C
NOTES
1
Stresses above those listed under Absolute Maximum Ratings may cause perma-
nent damage to the device. This is a stress rating only; functional operation of the
device at these or any other conditions above those listed in the operational
sections of this specification is not implied. Exposure to absolute maximum rating
conditions for extended periods may affect device reliability. Only one absolute
maximum rating may be applied at any one time.
2
Overvoltages at IN, S or D will be clamped by internal diodes. Current should be
limited to the maximum ratings given.
CAUTION
ESD (electrostatic discharge) sensitive device. Electrostatic charges as high as 4000 V readily
accumulate on the human body and test equipment and can discharge without detection.
Although the ADG417 features proprietary ESD protection circuitry, permanent damage may
occur on devices subjected to high energy electrostatic discharges. Therefore, proper ESD
precautions are recommended to avoid performance degradation or loss of functionality.
WARNING!
ESD SENSITIVE DEVICE
TERMINOLOGY
V
DD
V
SS
V
L
GND
S
D
IN
R
ON
I
S
(OFF)
I
D
(OFF)
I
D
, I
S
(ON)
Most positive power supply potential.
Most negative power supply potential in dual
supplies. In single supply applications, it
may be connected to GND.
Logic power supply (+5 V).
Ground (0 V) reference.
Source terminal. May be an input or an
output.
Drain terminal. May be an input or an
output.
Logic control input.
Ohmic resistance between D and S.
Source leakage current with the switch
“OFF.”
Drain leakage current with the switch
“OFF.”
Channel leakage current with the switch
“ON.”
Analog voltage on terminals D, S.
“OFF” switch source capacitance.
“OFF” switch drain capacitance.
“ON” switch capacitance.
Delay between applying the digital control
input and the output switching on.
Delay between applying the digital control
t
OFF
input and the output switching off.
Maximum input voltage for logic “0.”
V
INL
V
INH
Minimum input voltage for logic “1.”
I
INL
(I
INH
)
Input current of the digital input.
Charge Injection A measure of the glitch impulse transferred
from the digital input to the analog output
during switching.
Off Isolation
A measure of unwanted signal coupling
through an “OFF” channel.
Positive supply current.
I
DD
I
SS
Negative supply current.
I
L
Logic supply current.
V
D
(V
S
)
C
S
(OFF)
C
D
(OFF)
C
D
, C
S
(ON)
t
ON
–4–
REV. A
AD [ ANALOG DEVICES ]
