ADDAC80/ADDAC85/ADDAC87
Table V. External Op Amp Voltage Mode Connections
Output
Range
Digital
Input Codes
Connect
A to
Connect
Pin 17 to
Connect
Pin 19 to
Connect
Pin 16 to
10 V
5 V
2.5 V
0 V to 10 V
0 V to 5 V
COB or CTC 19
COB or CTC 18
COB or CTC 18
15
15
15
21
21
A
NC
15
NC
15
24
24
24
24
24
CSB
CSB
18
18
OUTLINE DIMENSIONS
Dimensions shown in inches and (mm).
24-Lead Plastic DIP (N-24A)
1.290 (32.70)
1.150 (29.30)
24
13
0.580 (14.73)
0.485 (12.32)
1
12
PIN 1
0.625 (15.87)
0.600 (15.24)
0.060 (1.52)
0.015 (0.38)
0.250
0.195 (4.95)
0.125 (3.18)
(6.35)
MAX
0.150
(3.81)
MIN
0.200 (5.05)
0.125 (3.18)
0.015 (0.381)
0.008 (0.204)
0.100
(2.54)
BSC
0.022 (0.558)
0.014 (0.356)
0.070 (1.77)
0.030 (0.77)
SEATING
PLANE
CONTROLLING DIMENSIONS ARE IN MILLIMETERS: INCH DIMENSIONS
ARE ROUNDED-OFF MILLIMETER EQUIVALENTS FOR REFERENCE
ONLY AND ARE NOT APPROPRIATE FOR USE IN DESIGN
24-Lead Ceramic DIP (D-24)
SEE NOTE 5
0.098 (2.49) MAX
13
0.005 (0.13) MIN
24
0.610 (15.49)
0.500 (12.70)
SEE NOTE 4
PIN 1
1
12
SEE NOTE 1
0.620 (15.75)
0.590 (14.99)
SEE NOTE 3
0.075 (1.91)
0.015 (0.38)
SEE NOTE 4
1.290 (32.77) MAX
0.225 (5.72)
MAX
0.150
(3.81)
MIN
SEATING
PLANE
0.200 (5.08)
0.120 (3.05)
0.015 (0.38)
0.008 (0.20)
SEE NOTE 6
0.023 (0.58)
0.014 (0.36)
0.070 (1.78)
0.030 (0.76)
0.110 (2.79)
0.090 (2.29)
SEE NOTE 7 SEE NOTE 2, 6
NOTES
1. INDEX AREA; A NOTCH OR A LEAD ONE IDENTIFICATION MARK IS LOCATED ADJACENT TO LEAD ONE.
2. THE MINIMUM LIMIT FOR DIMENSION MAY BE 0.023" (0.58 mm) FOR ALL FOUR CORNER LEADS ONLY.
3. DIMENSION SHALL BE MEASURED FROM THE SEATING PLANE TO THE BASE PLANE.
4. THIS DIMENSION ALLOWS FOR OFF-CENTER LID, MENISCUS AND GLASS OVERRUN.
5. APPLIES TO ALL FOUR CORNERS.
6. ALL LEADS — INCREASE MAXIMUM LIMIT BY 0.003" (0.08 mm) MEASURED AT THE CENTER OF THE FLAT,
WHEN HOT SOLDER DIP LEAD FINISH IS APPLIED.
7. TWENTY TWO SPACES.
8. CONTROLLING DIMENSIONS ARE IN MILLIMETERS. INCH DIMENSIONS ARE ROUNDED-OFF MILLIMETER
EQUIVALENTS FOR REFERENCE ONLY AND ARE NOT APPROPRIATE FOR USE IN DESIGN
REV. B
–13–
ADI [ ADI ]
