欢迎访问ic37.com |
会员登录 免费注册
发布采购

AL10051N3DL 参数 Datasheet PDF下载

AL10051N3DL图片预览
型号: AL10051N3DL
PDF下载: 下载PDF文件 查看货源
内容描述: 薄膜片式电感器 [THIN FILM CHIP INDUCTOR]
分类和应用: 电感器
文件页数/大小: 66 页 / 368 K
品牌: ABC [ ABC Taiwan Electronics Corp ]
 浏览型号AL10051N3DL的Datasheet PDF文件第23页浏览型号AL10051N3DL的Datasheet PDF文件第24页浏览型号AL10051N3DL的Datasheet PDF文件第25页浏览型号AL10051N3DL的Datasheet PDF文件第26页浏览型号AL10051N3DL的Datasheet PDF文件第28页浏览型号AL10051N3DL的Datasheet PDF文件第29页浏览型号AL10051N3DL的Datasheet PDF文件第30页浏览型号AL10051N3DL的Datasheet PDF文件第31页  
AL103 Revision 1.0  
this case, the flow control option is recommended so when the frame buffer is full, incoming frames  
will be backpressured. To prevent buffer starvation, half of the memory is reserved and allocated to  
each port while the other half is shared.  
The other option is to limit the number of frames that each output queue can store. This option is  
selected by setting bit 00.15 to “1.” An output queue watermark can be set in System Configuration  
Register I (Register 00, Bits 7:6) to keep the balance between utilization and fairness of buffer  
sharing. This method prevents other ports from suffering performance reduction due to a single port  
experiencing an extreme congestion. If severe congestion is experienced in a single port, only that  
port will suffer from frame loss because the buffer is limited to its dedicated portion. Other ports  
will not experience any frame loss due to congestion problem in other ports since all other ports  
retain their own allocated buffer space.  
When an output queue or multicast queue experiences a buffer full condition, the AL103 will  
backpressure the incoming frames if flow control is enabled. A watermark for buffer full condition  
can be selected in register 04.  
3.10 Uplink Port  
The uplink port provides a means to connect the switch with a repeater hub, a workgroup switch, a  
router, or any type of interconnecting device compliance with IEEE 802.3 standards.  
If flood control is enabled, the AL103 will send all frames with unmatched DA and multicast/  
broadcast frames to the uplink port. It is very important that each port is assigned to an uplink port  
via the Port Configuration Register (0D to1C), or data frames might be lost. The uplink port should  
be configured to be within the same VLAN of the source port. If the uplink port is not a member of  
the VLANs, the broadcast or multicast frames will not be forwarded to its designated uplink port.  
Multiple VLANs can share the same uplink port.  
The AL103 will direct the following frames to the uplink port:  
Frames with a unicast destination address that doesn’t match with any MAC  
address stored in the switch.  
Frames with a broadcast/multicast destination address if the uplink port is in the  
same VLAN.  
Note: When configuring an uplink port, the uplink port should designate itself as the uplink port.  
3.11 Port Monitoring  
The AL103 supports port monitoring. This feature provides complete network monitoring  
capability at 100 Mbit/s. A copy of egress (TX) data and ingress (RX) data of the monitored port is  
sent to their respective snooping ports.  
The monitored port is selected by register 30. The AL103 allows transmit and receive data to be  
monitored by different snooping ports. The snooping ports are also selected by register 30.  
9/00  
Reference Only / Allayer Communications  
27  
 
 
 复制成功!