欢迎访问ic37.com |
会员登录 免费注册
发布采购

ISL40 参数 Datasheet PDF下载

ISL40图片预览
型号: ISL40
PDF下载: 下载PDF文件 查看货源
内容描述: 独立的DC - LIN从异步通信在嘈杂的线路 [Independent DC-LIN Slave For Asynchronous Communication Over Noisy Lines]
分类和应用: 通信
文件页数/大小: 12 页 / 165 K
品牌: YAMAR [ YAMAR ELECTRONICS LTD. ]
 浏览型号ISL40的Datasheet PDF文件第1页浏览型号ISL40的Datasheet PDF文件第2页浏览型号ISL40的Datasheet PDF文件第3页浏览型号ISL40的Datasheet PDF文件第4页浏览型号ISL40的Datasheet PDF文件第6页浏览型号ISL40的Datasheet PDF文件第7页浏览型号ISL40的Datasheet PDF文件第8页浏览型号ISL40的Datasheet PDF文件第9页  
Proprietary and Confidential Information of YAMAR Electronics Ltd.  
Sync break  
Sync Field  
0x3C  
Zero byte/bytes  
Checksum  
Figure 3.5 Sleep message  
Change Frequency message:  
This type of message consists of 5 bytes - sync break, sync field, “FE” Hex, “00” Hex and checksum.  
The change frequency message identifier is “FE” Hex and the following data byte “00”Hex.  
Upon reception of sync break, sync field, “FE” Hex and “00” Hex bytes the frequency changes from F1  
to F0 or vise versa.  
Sync break  
Sync Field  
0xFE  
Zero byte/bytes  
Checksum  
Figure 3.6 Frequency Change message  
3.2  
Power Management  
The device features Sleep mode for power saving. Entering Sleep and waking up are done either  
locally by dedicated pins, or remotely through activity over the bus.  
3.2.1  
Entering Sleep mode  
The ISL40 can enter sleep mode in the following ways:  
1. Local device lowers its nSleep pin.  
2. Remote master SIG40 device can enter the ISL40 device into Sleep Mode from Normal mode by  
transmitting the remote sleep message.  
3. The AutoSleep pin is high and no reception occurred for about 8 seconds.  
3.2.2  
Remote wake up process  
The ISL40 can wakeup by a remote SIG40 master or ISL40 device transmits a wakeup message over  
the bus. During Sleep Mode, the ISL40 wakes up periodically to sense the bus for activity every  
32mSec. If a wakeup message is detected, the ISL40 device raises pin INH and lowers pin HDO. If  
nSleep pin is low upon remote waking up, the local device that lowered it must raise the nSleep back  
high. Figure 3.6 shows the signals description.  
Wakeup Message  
DC-BUS  
msg. detected  
INH  
HDO  
Normal mode  
Standby  
Figure 3.7 - Wakeup from bus message  
3.2.3  
Wakeup from pin Wake  
A transition on pin Wake (caused by an external switch of the application) is used to wake the device.  
The device then enters Standby mode, raises pin INH, and transmits a wakeup message to the bus.  
While transmitting the wakeup message to the bus, the device lowers pin HDO. After the transmission  
is complete the device raises pin HDO. After the transmission is completed the device enters Normal  
© 2007 Yamar Electronics Ltd.  
5
DS-ISL40 R1.6