AVPro® 5303B
Universal 3-Input A/V Switch Interface
DATA SHEET
Functional Description
A/V Input Source Selection
The device accepts up to three sets of A/V input
signals. Bits 0 & 1 of Register 0 determine which of the
sets will be present at the device’s output pins.
The 5303B is an analog A/V interface IC designed for
TV and general-purpose A/V applications. The device
accepts up to three sets of SCART input signals (Red,
Green, Blue, CVBS, R, L, Fast Blanking, and TV
Function). By way of 3:1 mux, SCART 1, 2, or 3 signals
can be selected at the device’s output pins. The 5303B
supports four SCART video modes: RGB/CVBS, RGB-
only, CVBS-only and SVHS. The RGB and CVBS video
driver gains are programmable from 2 to 1.4 in 0.2
steps, and the R/L audio driver gain can be 0dB or 6dB.
The R/L audio drivers can accept signals from 0.5Vrms
to 2Vrms.
Video Mode Selection
The device supports four video modes for TV SCART
applications: RGB/CVBS, RGB-only, CVBS-only, and
SVHS. Bits 2, 3, & 4 set the active video mode.
RGB/CVBS video mode is a default mode. For general-
purpose A/V applications, the device supports
YPrPb/CVBS and CVBS/SVHS video modes.
For general-purpose A/V applications, video switches
and drivers can be configured to support component
video (YPrPb), S-Video (SVHS), and composite video
(CVBS) signals.
RGB Gain
The gain of the RGB outputs can be adjusted to one of
four different levels. Bits 0 & 1 Register 1 set the gain
of the RGB output amplifiers according to the following
table:
All switching and programmable functions of the
device are controlled through a standard I2C serial
interface
Bit 1
Bit 0
RGB Amplifier Gain
0
0
1
1
0
1
0
1
Gain = 2 V/V
Gain = 1.8 V/V
Gain = 1.6 V/V
Gain = 1.4 V/V
DC Restore for RGB, Y, and CVBS: The device will
generate a DC restore level on each video output based
on timing referenced to a horizontal sync pulse. When
the sync pulse is detected, the DC restore circuit will act
to position the blank level to 1.2V at the respective RGB,
Y, or CVBS output pin(s).
CVBS Gain
The gain of the CVBS output can be adjusted to one of
four different levels. Bits 2 & 3 Register 1 set the gain
of the CVBS output amplifier according to the following
table:
DC Restore for SVHS and YPrPb: In the SVHS
mode, the CVBS pin is used as Luma input and the
Red pin is used as Chroma input. The DC restore
function for Luma signal is equivalent to CVBS signal.
The DC restore circuit will position the output blank level
to 1.2V at the respective Luma output pin. For the
Chroma input, the on-chip clamp circuit will be used to
position the output mid-scale DC level to 1.8V. In the
YPrPb mode, the mid-scale DC level for Pr and Pb
outputs will also be at 1.8V.
Bit 3
Bit 2
CVBS Amplifier Gain
0
0
1
1
0
1
0
1
Gain = 2 V/V
Gain = 1.8 V/V
Gain = 1.6 V/V
Gain = 1.4 V/V
Audio Gain
The gain of the R/L audio amplifiers can be set to either
0dB or 6dB. Bit 4 of Register 1 sets the gain of the
amplifiers according to the following table:
Bit 4
R/L Amplifier Gain
0
1
Gain = 0 dB
Gain = 6 dB
Page: 2 of 16
© 2005 TERIDIAN Semiconductor Corporation
Rev 1.0
TERIDIAN [ TERIDIAN SEMICONDUCTOR CORPORATION ]
