CY2SSTV16859
Absolute Maximum Conditions[4,5]
Parameter
[6]
Description
Terminal Voltage with respect to VSS
Terminal Voltage with respect to VSS
Storage Temperature
Condition
Min.
–0.5
–0.5
–65°
–50
Max.
3.6
Unit
V
VTERM
[7]
VTERM
VDD + 0.5
150°C
50
V
TSTG
IOUT
IIK
°C
DC Output Current
mA
mA
mA
mA
Continuous Clamp Current
VI<0 or VI>VSS
–50
50
IOK
Continuous Clamp Current
VO<0 or VO>VDD
–50
50
Idd
ISS
Continuous Current through each VDD, VDDQ or VSS
–100
100
Recommended Operating Conditions[8]
Parameter
VDD
Description
Min.
Typ.
Max.
Unit
V
Supply voltage
2.3
2.5
2.5
2.6
1.25
1.3
VREF
–
2.7
VDDQ
Outputsupplyvoltage PC1600,PC2100,PC2700
PC3200
2.3
2.7
V
2.5
2.7
V
VREF
Reference voltage
(VREF = VDDQ/2)
PC1600,PC2100,PC2700
PC3200
1.15
1.35
V
1.25
1.35
V
VTT
VI
Termination voltage
Input voltage
VREF – 40 mV
VREF + 40 mV
V
0
VDD
V
VIH
VIL
AC Data Input high-level voltage
AC Data Input low-level voltage
DC Data Input high-level voltage
DC Data Input low-level voltage
RESET# Input high-level voltage
RESET# Input low-level voltage
CLK, CLK# Common-mode input voltage range
CLK, CLK# Peak-to-peak input voltage
High-level output current
VREF + 310 mV
–
–
V
–
–
VREF – 310 mV
V
VIH
VIL
VREF + 150 mV
–
–
V
–
1.7
–
–
VREF – 150 mV
V
VIH
VIL
–
–
0.7
1.53
–
V
–
V
VICR
VI(PP)
IOH
IOL
0.97
360
–
–
V
–
mV
mA
mA
°C
–
–20
20
Low-level output current
–
–
TA
Operating free-air temperature
0
–
85
DC Electrical Specifications
Parameter
VIK
Description
Condition
VDD
2.3V
Min.
Typ.[9] Max. Unit
Clamp Voltage II = –18 mA
–
–
–
–
–
–
–
–
–
–1.2
–
V
V
VOH
High level output IOH = –100 µA
voltage
2.3 to 2.7V VDD – 0.2
I
OH = –16 mA
2.3V
2.3 to 2.7V
2.3
1.95
–
V
VOL
Low level output IOL = 100 µA
voltage
–
–
–
–
–
0.2
0.35
5
V
I
OL = 16 mA
V
II
All Inputs
VI = VDD or VSS
RESET# = VSS
2.7V
µA
µA
mA
IDD
Static Standby
IO = 0
2.7V
10
Static Operating RESET# = VDD, VI = VIH(AC) or VIL(AC)
2.7
40.0
Notes:
4. The voltage on any input or I/O pin cannot exceed the power pin during power-up. Power supply sequencing is NOT required.
5. Stresses greater than those listed under Absolute Maximum Conditions may cause permanent damage to the device. This is a stress rating only and functional
operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied. Exposure to absolute
maximum rating conditions for extended period may affect reliability.
6. V /V
terminals.
7. All terminals except V
DD DDQ
.
DD
8. The RESET# input of the device must be held at V or V to ensure proper device operation.
DD
SS
9. All typical values are measured at T
= 25°C
AMB
Rev 1.0,November 21, 2006
Page 3 of 7
SPECTRALINEAR [ SPECTRALINEAR INC ]
