ESMT
M12L64164A (2M)
SIMPLIFIED TRUTH TABLE
A11,
A9~A0
BA0
BA1
COMMAND
CKEn-1 CKEn
DQM
CS RAS CAS WE
Note
A10/AP
1,2
3
Register
Refresh
Mode Register set
Auto Refresh
H
H
X
H
L
L
L
L
L
L
L
L
X
OP CODE
X
H
X
3
Entry
Self
3
Refresh
L
H
L
H
X
L
H
X
H
H
X
H
X
X
X
Exit
L
H
H
H
X
X
X
3
Bank Active & Row Addr.
V
V
Row Address
Auto Precharge Disable
L
Column
Address
(A0~A7)
4
Read &
L
H
L
H
X
Column Address
Auto Precharge Enable
Auto Precharge Disable
H
L
4,5
4
Column
Address
(A0~A7)
Write &
H
H
H
X
X
X
L
L
L
H
H
L
L
H
H
L
L
L
X
X
X
V
Column Address
Auto Precharge Enable
H
4,5
6
Burst Stop
X
Bank Selection
All Banks
V
X
L
Precharge
X
H
H
L
X
V
X
X
V
X
X
V
X
Clock Suspend or
Active Power Down
Entry
Exit
H
L
L
H
L
X
X
X
X
X
X
H
L
X
H
X
V
X
H
X
V
X
H
X
V
Entry
H
Precharge Power Down Mode
H
L
Exit
L
H
X
X
DQM
H
H
X
X
H
V
X
X
X
7
H
L
X
H
X
H
No Operating Command
(V = Valid, X = Don’t Care. H = Logic High, L = Logic Low)
Note:
1.OP Code: Operating Code
A0~A11 & BA0, BA1: Program keys. (@ MRS)
2.MRS can be issued only at all banks precharge state.
A new command can be issued after 2 CLK cycles of MRS.
3.Auto refresh functions are as same as CBR refresh of DRAM.
The automatical precharge without row precharge of command is meant by “Auto”.
Auto/self refresh can be issued only at all banks idle state.
4.BA0, BA1 : Bank select addresses.
If both BA0 and BA1 are “Low” at read, write, row active and precharge, bank A is selected.
If both BA0 is “Low” and BA1 is “High” at read, write, row active and precharge, bank B is selected.
If both BA0 is “High” and BA1 is “Low” at read, write, row active and precharge, bank C is selected.
If both BA0 and BA1 are “High” at read, write, row active and precharge, bank D is selected
If A10/AP is “High” at row precharge, BA0 and BA1 is ignored and all banks are selected.
5.During burst read or write with auto precharge, new read/write command can not be issued.
Another bank read/write command can be issued after the end of burst.
New row active of the associated bank can be issued at tRP after the end of burst.
6.Burst stop command is valid at every burst length.
7.DQM sampled at positive going edge of a CLK and masks the data-in at the very CLK (write DQM latency is 0), but
makes Hi-Z state the data-out of 2 CLK cycles after.(Read DQM latency is 2)
Elite Semiconductor Memory Technology Inc.
Publication Date: Apr. 2012
Revision: 1.6 7/45
ESMT [ ELITE SEMICONDUCTOR MEMORY TECHNOLOGY INC. ]
