CAT24C01B
ABSOLUTE MAXIMUM RATINGS*
*COMMENT
Temperature Under Bias ................. –55°C to +125°C
Storage Temperature....................... –65°C to +150°C
Stresses above those listed under “Absolute Maximum
Ratings” may cause permanent damage to the device.
These are stress ratings only, and functional operation of
the device at these or any other conditions outside of those
listed in the operational sections of this specification is not
implied. Exposure to any absolute maximum rating for
extended periods may affect device performance and
reliability.
Voltage on Any Pin with
Respect to Ground(1) ........... –2.0V to +VCC + 2.0V
VCC with Respect to Ground ............... –2.0V to +7.0V
Package Power Dissipation
Capability (Ta = 25°C) .................................. 1.0W
Lead Soldering Temperature (10 secs) ............ 300°C
Output Short Circuit Current(2) ........................ 100mA
RELIABILITY CHARACTERISTICS
Symbol
Parameter
Endurance
Min.
1,000,000
100
Max.
Units
Cycles/Byte
Years
Reference Test Method
MIL-STD-883, Test Method 1033
MIL-STD-883, Test Method 1008
MIL-STD-883, Test Method 3015
JEDEC Standard 17
(3)
NEND
(3)
TDR
Data Retention
ESD Susceptibility
Latch-up
(3)
VZAP
2000
Volts
(3)(4)
ILTH
100
mA
D.C. OPERATING CHARACTERISTICS
V
= +1.8V to +6.0V, unless otherwise specified.
CC
Limits
Typ.
Symbol
Parameter
Min.
Max.
Units
mA
µA
µA
µA
V
Test Conditions
fSCL = 100 KHz
ICC
Power Supply Current
3
(5)
ISB
Standby Current (VCC = 5.0V)
Input Leakage Current
0
10
VIN = GND or VCC
VIN = GND to VCC
VOUT = GND to VCC
ILI
ILO
Output Leakage Current
Input Low Voltage
10
VIL
–1
VCC x 0.3
VCC + 0.5
0.4
VIH
Input High Voltage
VCC x 0.7
V
VOL1
VOL2
Output Low Voltage (VCC = 3.0V)
Output Low Voltage (VCC = 1.8V)
V
IOL = 3 mA
0.5
V
IOL = 1.5 mA
CAPACITANCE T = 25°C, f = 1.0 MHz, V
= 5V
A
CC
Symbol
Test
Input/Output Capacitance (SDA)
Input Capacitance (A0, A1, A2, SCL, WP)
Max.
Units
Conditions
VI/O = 0V
VIN = 0V
(3)
CI/O
8
6
pF
pF
(3)
CIN
Note:
(1) The minimum DC input voltage is –0.5V. During transitions, inputs may undershoot to –2.0V for periods of less than 20 ns. Maximum DC
voltage on output pins is V +0.5V, which may overshoot to V + 2.0V for periods of less than 20ns.
CC
CC
(2) Output shorted for no more than one second. No more than one output shorted at a time.
(3) This parameter is tested initially and after a design or process change that affects the parameter.
(4) Latch-up protection is provided for stresses up to 100 mA on address and data pins from –1V to V +1V.
CC
(5) Standby Current (I ) = 0µA (<900nA).
SB
Doc. No. 25085-00 7/99 S-1
2
CATALYST [ CATALYST SEMICONDUCTOR ]
