A24C04
AiT Semiconductor Inc.
www.ait-ic.com
MEMORY EEPROM
4k BITS (512 X 8) TWO-WIRE SERIAL
DC ELECTRICAL CHARACTERISTICS
Applicable over recommended operating range from: TA = -40℃ to +85℃, VCC = +1.7V to +5.5V, unless otherwise noted
Parameter
Supply Voltage
Supply Voltage
Symbol
VCC1
VCC2
ICC1
Condition
Min.
Typ.
-
Max.
5.5
Unit
V
1.7
2.5
-
0.14
0.28
0.03
0.10
0.05
-
5.5
V
Supply Current VCC = 5.0V
Supply Current VCC = 5.0V
Supply Current VCC = 5.0V
Input Leakage Current
Output Leakage Current
Input Low Level
Input High Level
Output Low Level VCC = 1.7V
Output Low Level VCC = 5.0V
Read at 400kHz
Write at 400kHz
VIN = VCC or VSS
VIN = VCC or VSS
VOUT = VCC or VSS
VCC = 1.7V to 5.5V
VCC = 1.7V to 5.5V VCC x0.7
IOL = 0.15mA
IOL = 3.0mA
-
0.3
mA
mA
μA
μA
μA
V
ICC2
-
0.5
ISB1
-
0.5
ILI
ILO
-
-
1.0
1.0
VIL1
-0.3
VCC x 0.3
VCC + 0.3
0.2
VIH1
VOL1
VOL2
-
V
-
-
-
V
-
0.4
V
AC ELECTRICAL CHARACTERISTICS
Applicable over recommended operating range from: TA = -40℃ to +85℃, VCC = +1.7V to +5.5V, CL = 1 TTL
Gate and 100pF, unless otherwise noted
1.7V≤VCC<2.5V
2.5V≤VCC<5.5V
Parameter
Symbol
Unit
Min.
Typ.
Max.
Min.
Typ.
Max.
Clock Frequency, SCL
Clock Pulse Width Low
Clock Pulse Width High
Noise Suppression Time
Clock Low to Data Out Valid
Time the bus must be free before
a new transmission can start
Start Hold Time
fSCL
tLOW
tHIGH
tI
-
-
-
-
-
-
400
-
-
-
-
-
-
1000
-
-
50
0.55
kHz
μs
0.6
0.4
-
-
0.6
0.4
-
-
μs
50
0.55
ns
μs
tAA
0.1
0.1
tBUF
0.5
-
-
0.5
-
-
μs
tHD.STA
tSU.STA
tHD.DAT
tSU.DAT
tR
0.25
0.25
0
100
-
-
0.25
50
-
-
-
0.25
0.25
0
100
-
-
0.25
50
-
-
-
μs
μs
Start Setup Time
-
-
-
-
-
-
Data In Hold Time
-
-
μs
Data In Setup Time
-
-
-
-
ns
Inputs Rise TimeNOTE1
Inputs Fall TimeNOTE1
Stop Setup Time
-
-
0.3
0.3
-
-
-
0.3
0.3
-
μs
tF
μs
tSU.STO
-
-
-
-
μs
Data Out Hold Time
Write Cycle Time
tDH
tWR
-
3
-
3
ns
1.9
1.9
ms
Write
Cycles
5.0V, 25℃, Byte ModeNOTE1
Endurance
1M
-
-
-
-
-
NOTE1: This parameter is characterized and is not 100% tested.
NOTE2: AC measurement conditions: RL(connects to VCC): 1.3kΩ
Input pulse voltages: 0.3 VCC to 0.7VCC
Input rise and fall time: 50ns
Input and output timing reference voltages: 0.5VCC
The value of RL should be concerned according to the actual loading on the user’s system.
REV2.0
- SEP 2008 RELEASED, NOV 2016 UPDATED -
- 4 -