HIGH SPEED-10 MBit/s
LOGIC GATE OPTOCOUPLERS
SINGLE-CHANNEL
6N137
HCPL-2601
HCPL-2611
TRANSFER CHARACTERISTICS
DC Characteristics
High Level Output Current
Low Level Output Current
(T
A
= -40°C to +85°C Unless otherwise specified.)
Test Conditions
(V
CC
= 5.5 V, V
O
= 5.5 V)
(I
F
= 250 µA, V
E
= 2.0 V) (Note 2)
(V
CC
= 5.5 V, I
F
= 5 mA)
(V
E
= 2.0 V, I
CL
= 13 mA) (Note 2)
Input Threshold Current
(V
CC
= 5.5 V, V
O
= 0.6 V,
V
E
= 2.0 V, I
OL
= 13 mA)
Symbol
I
OH
V
OL
I
FT
.35
3
Min
Typ**
Max
100
0.6
5
Unit
µA
V
mA
DUAL-CHANNEL
HCPL-2630
HCPL-2631
ISOLATION CHARACTERISTICS
Characteristics
Input-Output
Insulation Leakage Current
(T
A
= -40°C to +85°C Unless otherwise specified.)
Test Conditions
Symbol
Min
Typ**
Max
Unit
(Relative humidity = 45%)
(T
A
= 25°C, t = 5 s)
(V
I-O
= 3000 VDC)
(Note 12)
I
I-O
1.0*
µA
Withstand Insulation Test Voltage
Resistance (Input to Output)
Capacitance (Input to Output)
(RH < 50%, T
A
= 25°C)
(Note 12) ( t = 1 min.)
(V
I-O
= 500 V) (Note 12)
(f = 1 MHz) (Note 12)
V
ISO
R
I-O
C
I-O
2500
10
12
0.6
V
RMS
pF
** All typical values are at V
CC
= 5 V, T
A
= 25°C
NOTES
The V
CC
supply to each optoisolator must be bypassed by a 0.1µF capacitor or larger. This can be either a ceramic or solid tantalum
capacitor with good high frequency characteristic and should be connected as close as possible to the package V
CC
and GND pins
of each device.
2. Each channel.
3. Enable Input - No pull up resistor required as the device has an internal pull up resistor.
4. t
PLH
- Propagation delay is measured from the 3.75 mA level on the HIGH to LOW transition of the input current pulse to the 1.5 V
level on the LOW to HIGH transition of the output voltage pulse.
5. t
PHL
- Propagation delay is measured from the 3.75 mA level on the LOW to HIGH transition of the input current pulse to the 1.5 V
level on the HIGH to LOW transition of the output voltage pulse.
6. t
r
- Rise time is measured from the 90% to the 10% levels on the LOW to HIGH transition of the output pulse.
7. t
f
- Fall time is measured from the 10% to the 90% levels on the HIGH to LOW transition of the output pulse.
8. t
ELH
- Enable input propagation delay is measured from the 1.5 V level on the HIGH to LOW transition of the input voltage pulse
to the 1.5 V level on the LOW to HIGH transition of the output voltage pulse.
9. t
EHL
- Enable input propagation delay is measured from the 1.5 V level on the LOW to HIGH transition of the input voltage pulse
to the 1.5 V level on the HIGH to LOW transition of the output voltage pulse.
10. CM
H
- The maximum tolerable rate of rise of the common mode voltage to ensure the output will remain in the high state
(i.e., V
OUT
> 2.0 V). Measured in volts per microsecond (V/µs).
11. CM
L
- The maximum tolerable rate of rise of the common mode voltage to ensure the output will remain in the low output state
(i.e., V
OUT
< 0.8 V). Measured in volts per microsecond (V/µs).
12. Device considered a two-terminal device: Pins 1,2,3 and 4 shorted together, and Pins 5,6,7 and 8 shorted together.
1.
www.fairchildsemi.com
4 OF 11
7/9/01
DS300202
ETC [ ETC ]
