PIC16F87X
2.3
PCL and PCLATH
Note 1: There are no status bits to indicate stack
overflow or stack underflow conditions.
The program counter (PC) is 13-bits wide. The low byte
comes from the PCL register, which is a readable and
writable register. The upper bits (PC<12:8>) are not
readable, but are indirectly writable through the
PCLATH register. On any reset, the upper bits of the PC
will be cleared. Figure 2-5 shows the two situations for
the loading of the PC. The upper example in the figure
shows how the PC is loaded on a write to PCL
(PCLATH<4:0> → PCH). The lower example in the fig-
ure shows how the PC is loaded during a CALLor GOTO
instruction (PCLATH<4:3> → PCH).
2: There are no instructions/mnemonics
called PUSHor POP. These are actions that
occur from the execution of the CALL,
RETURN, RETLW and RETFIE instruc-
tions or the vectoring to an interrupt
address.
2.4
Program Memory Paging
PIC16CXX devices are capable of addressing a contin-
uous 8K word block of program memory. The CALLand
GOTO instructions provide only 11 bits of address to
allow branching within any 2K program memory page.
When doing a CALL or GOTO instruction, the upper 2
bits of the address are provided by PCLATH<4:3>.
When doing a CALLor GOTOinstruction, the user must
ensure that the page select bits are programmed so
that the desired program memory page is addressed. If
a return from a CALL instruction (or interrupt) is exe-
cuted, the entire 13-bit PC is popped off the stack.
Therefore, manipulation of the PCLATH<4:3> bits are
not required for the return instructions (which POPs the
address from the stack)
FIGURE 2-5: LOADING OF PC IN
DIFFERENT SITUATIONS
PCH
PCL
12
8
7
0
Instruction with
PCL as
PC
Destination
8
PCLATH<4:0>
PCLATH
5
ALU
PCH
12 11 10
PCL
Example 2-1 shows the calling of a subroutine in
page 1 of the program memory. This example assumes
that PCLATH is saved and restored by the interrupt ser-
vice routine (if interrupts are used).
8
7
0
GOTO,CALL
PC
PCLATH<4:3>
PCLATH
11
2
Opcode <10:0>
EXAMPLE 2-1: CALL OF A SUBROUTINE IN
PAGE 1 FROM PAGE 0
ORG 0x500
BCF PCLATH,4
BSF PCLATH,3
CALLSUB1_P1
;Select page 1 (800h-FFFh)
;Call subroutine in
2.3.1
COMPUTED GOTO
:
:
;page 1 (800h-FFFh)
A computed GOTOis accomplished by adding an offset
to the program counter (ADDWF PCL). When doing a
table read using a computed GOTO method, care
should be exercised if the table location crosses a PCL
memory boundary (each 256 byte block). Refer to the
ORG 0x900
;page 1 (800h-FFFh)
SUB1_P1
:
:
:
;called subroutine
;page 1 (800h-FFFh)
application note, “Implementing
a
Table Read"
RETURN
;return to Call subroutine
;in page 0 (000h-7FFh)
(AN556).
2.3.2
STACK
The PIC16CXX family has an 8-level deep x 13-bit wide
hardware stack. The stack space is not part of either
program or data space and the stack pointer is not
readable or writable. The PC is PUSHed onto the stack
when a CALL instruction is executed or an interrupt
causes a branch. The stack is POPed in the event of a
RETURN,RETLW or a RETFIE instruction execution.
PCLATH is not affected by a PUSHor POPoperation.
The stack operates as a circular buffer. This means that
after the stack has been PUSHed eight times, the ninth
push overwrites the value that was stored from the first
push. The tenth push overwrites the second push (and
so on).
DS30292B-page 26
1999 Microchip Technology Inc.