Embossed Carrier Configuration
8 & 12mm Tape Only
8 & 12mm Embossed Tape
Metric Dimensions Will Govern
CONSTANT DIMENSIONS
Tape Size
8mm
and
12mm
D
0
8.4
+0.10
-0.0
(.059
+.004
)
-0.0
E
P
0
P
2
T Max.
0.600
(.024)
T
1
0.10
(.004)
Max.
G
1
0.75
(.030)
Min.
See Note 3
G
2
0.75
(.030)
Min.
See Note 4
1.75 ± 0.10
4.0 ± 0.10
2.0 ± 0.05
(.069 ± .004) (.157 ± .004) (.079 ± .002)
VARIABLE DIMENSIONS
Tape Size
B
1
D
1
Max.
Min.
See Note 6 See Note 5
4.55
(.179)
8.2
(.323)
4.55
(.179)
8.2
(.323)
1.0
(.039)
1.5
(.059)
1.0
(.039)
1.5
(.059)
F
P
1
R
Min.
See Note 2
25
(.984)
30
(1.181)
25
(.984)
30
(1.181)
T
2
W
A
0
B
0
K
0
8mm
3.5 ± 0.05
4.0 ± 0.10
(.138 ± .002) (.157 ± .004)
5.5 ± 0.05
4.0 ± 0.10
(.217 ± .002) (.157 ± .004)
3.5 ± 0.05
2.0 ± 0.10
(.138 ± .002) 0.79 ± .004
5.5 ± 0.05
8.0 ± 0.10
(.217 ± .002) (.315 ± .004)
2.5 Max
(.098)
6.5 Max.
(.256)
2.5 Max.
(.098)
6.5 Max.
(.256)
8.0
+0.3
-0.1
(.315
+.012
)
-.004
12.0 ± .30
(.472 ± .012)
8.0
+0.3
-0.1
(.315
+.012
)
-.004
12.0 ± .30
(.472 ± .012)
See Note 1
12mm
8mm
1/2 Pitch
12mm
Double
Pitch
See Note 1
See Note 1
See Note 1
NOTES:
1. A
0
, B
0
, and K
0
are determined by the max. dimensions to the ends of the terminals extending from the component body and/or the body dimensions of the component. The
clearance between the end of the terminals or body of the component to the sides and depth of the cavity (A
0
, B
0
, and K
0
) must be within 0.05 mm (.002) min. and 0.50 mm
(.020) max. The clearance allowed must also prevent rotation of the component within the cavity of not more than 20 degrees (see sketches C & D).
2. Tape with components shall pass around radius “R” without damage. The minimum trailer length (Note 2 Fig. 3) may require additional length to provide R min. for 12 mm
embossed tape for reels with hub diameters approaching N min. (Table 4).
3. G
1
dimension is the flat area from the edge of the sprocket hole to either the outward deformation of the carrier tape between the embossed cavities or to the edge of the
cavity whichever is less.
4. G
2
dimension is the flat area from the edge of the carrier tape opposite the sprocket holes to either the outward deformation of the carrier tape between the embossed cavity
or to the edge of the cavity whichever is less.
5. The embossment hole location shall be measured from the sprocket hole controlling the location of the embossment.
Dimensions of embossment location and hole location shall be applied independent of each other.
6. B
1
dimension is a reference dimension for tape feeder clearance only.
33
ETC [ ETC ]
