OUTPUT VOLTAGE & CURRENT RATINGS
Output
Voltage
3.3 V (2.64-3.96)
5.0 V (3.96-6.00)
7.5 V (5.25-8.25)
12.0 V (8.25-13.2)
15.0 V (10.50-16.5)
24.0 V (16.5-26.4)
36.0 V (25.2-39.6)
48.0 V (38.4-56.0)
Current
Max
120 A
120 A
80 A
53 A
43 A
27 A
18 A
13 A
Peak
-
-
-
-
-
31 A
(1)
-
Regulation
Line
20 mV
20 mV
36 mV
48 mV
60 mV
96 mV
144 mV
192 mV
Load
40 mV
40 mV
60 mV
100 mV
120 mV
150 mV
150 mV
300 mV
Ripple
Noise
(2)
120 mV
120 mV
150 mV
150 mV
150 mV
150 mV
200 mV
200 mV
Efficiency
(3)
72%
77%
79%
82%
82%
84%
84%
83%
CPB
Model
CPB600PS3V3
CPB600PS05
CPB600PS7V5
CPB600PS12
CPB600PS15
CPB600PS24
CPB600PS36
CPB600PS48
•
Notes
1. Peak current duration 100 ms max with a duty cycle
≤35%
170-264 VAC only.
2. Measured over a 20 MHz bandwidth and from 0 °C to +50 °C.
3. Measured at nominal 230 VAC input and 100% load.
Mechanical Details
Weight 3.4kg
Pin
1
2
3
4
5
6
7
8
9
10
CN1/CN2 PIN CONNECTIONS
Function
+M
+ Output Voltage Monitoring
+S
+ Remote Sensing
-M
- Output Voltage Monitoring
-S
- Remote Sensing
VB
Voltage Balance
CB
Current Balance
TRM Adjustment of Output Voltage
-S
- Remote Sensing
RC2 Remote ON/OFF
RCG Remote ON/OFF Ground
Pin
1
2
3
4
5
6
7
8
CN3 PIN CONNECTIONS
Function
-S
- Remote Sensing
-S
- Remote Sensing
AUX
Auxiliary Output (12 V/0.1A)
RC1
Remote ON/OFF
AUXG AUX Ground
N.C.
No Connection
PG
Power Good Signal
PGG
Power Good Ground
Output Voltage Adjustment
60-110% of the rated output voltage is achieved by:
1. Using on-board potentiometer.
2. Applying a voltage externally between TRM & -S
on CN1 or CN2.
3. Connecting a resistor externally between TRM & -S
on CN1 or CN2.
The external voltage level is calculated below &
should not be less than -0.7 V or more than 3.0 V.
External Trim Voltage =
Required Vout x 2.5
Vnom
Mating Connector & Terminal for CN1, CN2 & CN3
Connector
CN1
S10B-PHDSS
CN2
CN3 S8B-PHDSS
Mating
Connector
PHDR-10VS
PHDR-8VS
Terminal
Reel
Loose
SPHD-002T-P0.5
BPHD-001T-P0.5
BPHD-002T-P0.5
J.S.T
Mfr
www.xpplc.com
sales@xpplc.com
Rev 2.0
XPPOWER [ XP POWER LIMITED ]
