R
MultiPRO Desktop Tool
Table 5: SS/JTAG/SPI Port: 14-Pin Ribbon Cable Connector (Cont’d)
Ribbon
Cable
Number
Slave-Serial
JTAG
SPI(2)
Configuration Configuration Programming Type
Description
Mode
Mode
Mode
Test Mode Select. This is the JTAG mode signal that establishes
appropriate TAP state transitions for target ISP devices. It should be
connected to the TMS pin on all target ISP devices that share the
same data stream.
4
–
TMS
–
Out
Test Clock. This is the clock signal for JTAG operations, and should
be connected to the TCK pin on all target ISP devices that share the
same data stream.
6
–
TCK
–
Out
Test Data Out. This is the serial data stream received from the TDO
8
–
–
–
–
–
TDO
TDI
–
–
–
In
pin on the last device in a JTAG chain.
Test Data In. This is the serial data stream transmitted to the TDI pin
on the first device in a JTAG chain.
10
Out
SPI Select. This pin is the active-Low SPI chip select signal. This
4
6
SS
Out
Out
(2)
should be connected to the S pin on the SPI flash PROM.
SPI Clock. This pin is the clock signal for SPI operations and should
–
SCK
(2)
be connected to the C pin on the SPI flash PROM.
SPI Master-Input, Slave-Output. This pin is the target serial output
–
(2)
8
MISO
In
data stream for SPI operations and should be connected to the Q
pin on the SPI flash PROM.
SPI Master-Output Slave-Input. This pin is the target serial input
–
–
–
–
(2)
10
MOSI
–
Out
–
data stream for SPI operations and should be connected to the D
pin on the SPI flash PROM.
(1)
Digital Ground.
1, 3, 5, 7,
9, 11, 13
Notes:
1. All odd pins (1, 3, 5, 7, 9, 11, and 13) should be connected to digital ground on the target end of the ribbon cable. Minimum crosstalk is
achieved when using all grounds.
2. The listed SPI pin names match those of SPI flash memories from STMicroelectronics. Pin names of compatible SPI devices from other
vendors can be different. Consult the vendor's SPI device data sheet for corresponding pin names.
Caution! The PROG_B pin of the FPGA, which is connected to a target SPI device, must be asserted Low during SPI programming to
ensure the FPGA does not contend with the SPI programming operation.
3. The target reference voltage must be regulated and must not have a current-limiting resistor in series with the V
pin.
REF
Table 6: SelectMAP Port: 34-Pin Ribbon Cable Connector Interface Pin Descriptions
Ribbon Cable Pin
Number
SelectMAP
Configuration Mode
Type
Description
16
14
12
10
8
D0
D1
BIDIR
BIDIR
BIDIR
BIDIR
BIDIR
BIDIR
BIDIR
BIDIR
OUT
Byte-Wide Data Bus, Bit 0
Byte-Wide Data Bus, Bit 1
Byte-Wide Data Bus, Bit 2
Byte-Wide Data Bus, Bit 3
Byte-Wide Data Bus, Bit 4
Byte-Wide Data Bus, Bit 5
Byte-Wide Data Bus, Bit 6
Byte-Wide Data Bus, Bit 7
Configuration Clock
D2
D3
D4
6
D5
4
D6
2
D7
18
20
22
24
26
CCLK
RDWR
BUSY
DONE
INIT
OUT
Configuration Read / Write Control
Configuration Flow Control
Configuration Done
IN
IN
BIDIR
Configuration Initialize
DS114 (v1.9) February 8, 2008
www.xilinx.com
Product Specification
8
XILINX [ XILINX, INC ]
