欢迎访问ic37.com |
会员登录 免费注册
发布采购

X1228S14I 参数 Datasheet PDF下载

X1228S14I图片预览
型号: X1228S14I
PDF下载: 下载PDF文件 查看货源
内容描述: 实时时钟/日历/ CPU监控器, EEPROM [Real Time Clock/Calendar/CPU Supervisor with EEPROM]
分类和应用: 监控可编程只读存储器电动程控只读存储器电可擦编程只读存储器时钟
文件页数/大小: 31 页 / 568 K
品牌: XICOR [ XICOR INC. ]
 浏览型号X1228S14I的Datasheet PDF文件第1页浏览型号X1228S14I的Datasheet PDF文件第2页浏览型号X1228S14I的Datasheet PDF文件第3页浏览型号X1228S14I的Datasheet PDF文件第4页浏览型号X1228S14I的Datasheet PDF文件第6页浏览型号X1228S14I的Datasheet PDF文件第7页浏览型号X1228S14I的Datasheet PDF文件第8页浏览型号X1228S14I的Datasheet PDF文件第9页  
X1228
Notes:
(1) The device enters the Active state after any start, and remains active: for 9 clock cycles if the Device Select Bits in the Slave
Address Byte are incorrect or until 200nS after a stop ending a read or write operation.
(2) The device enters the Program state 200nS after a stop ending a write operation and continues for t
WC
.
(3) The device goes into the Timekeeping state 200nS after any stop, except those that initiate a nonvolatile write cycle; t
WC
after a
stop that initiates a nonvolatile write cycle; or 9 clock cycles after any start that is not followed by the correct Device Select Bits in
the Slave Address Byte.
(4) For reference only and not tested.
(5) V
IL
= V
CC
x 0.1, V
IH
= V
CC
x 0.9, f
SCL
= 400KHz
(6) V
CC
= 0V
(7) V
BACK
= 0V
(8) V
SDA
= V
SCL
=V
CC
, Others = GND or V
CC
(9) V
SDA
=V
SCL
=V
BACK
, Others = GND or V
BACK
(10) V
SDA
= GND or V
CC
, V
SCL
= GND or V
CC
, V
RESET
= V
CC
or GND
(11) I
OL
= 3.0mA at 5.5V, 1.5mA at 2.7V
(12) I
OH
= -1.0mA at 5.5V, -0.4mA at 2.7V
(13) Threshold voltages based on the higher of Vcc or Vback.
(14) Using recommended crystal and oscillator network applied to X1 and X2 (25°C).
(15) Typical values are for T
A
= 25°C
Capacitance
T
A
= 25°C, f = 1.0 MHz, V
CC
= 5V
Symbol
C
OUT
(1)
C
IN
(1)
Parameter
Output Capacitance (SDA, PHZ/IRQ, RESET)
Input Capacitance (SCL)
Max.
10
10
Units
pF
pF
Test Conditions
V
OUT
= 0V
V
IN
= 0V
Notes:
(1) This parameter is not 100% tested.
(2) The input capacitance between x1 and x2 pins can be varied between 5pF and 19.75pF by using analog trimming registers
AC CHARACTERISTICS
AC Test Conditions
Input Pulse Levels
Input Rise and Fall Times
Input and Output Timing
Levels
Output Load
V
CC
x 0.1 to V
CC
x 0.9
10ns
V
CC
x 0.5
Standard Output Load
Figure 18. Standard Output Load for testing the device with V
CC
= 5.0V
Equivalent AC Output Load Circuit for V
CC
= 5V
5.0V
5.0V
1533Ω
SDA
100pF
For V
OL
= 0.4V
and I
OL
= 3 mA
PHZ/IRQ
1316Ω
806Ω
100pF
REV 1.3 3/24/04
www.xicor.com
Characteristics subject to change without notice.
5 of 31