欢迎访问ic37.com |
会员登录 免费注册
发布采购

EV14D130K-J 参数 Datasheet PDF下载

EV14D130K-J图片预览
型号: EV14D130K-J
PDF下载: 下载PDF文件 查看货源
内容描述: [Metal Oxide Varistors]
分类和应用:
文件页数/大小: 59 页 / 2142 K
品牌: WPI [ World Produts Inc. ]
 浏览型号EV14D130K-J的Datasheet PDF文件第1页浏览型号EV14D130K-J的Datasheet PDF文件第2页浏览型号EV14D130K-J的Datasheet PDF文件第3页浏览型号EV14D130K-J的Datasheet PDF文件第5页浏览型号EV14D130K-J的Datasheet PDF文件第6页浏览型号EV14D130K-J的Datasheet PDF文件第7页浏览型号EV14D130K-J的Datasheet PDF文件第8页浏览型号EV14D130K-J的Datasheet PDF文件第9页  
Metal Oxide VaristOrs - eV series  
Definition of Terms (according to IEEE specifications C62.33)  
Average Power Dissipation: Tested using two consecutive pulses at rated peak current using a 10/1000µs test  
waveform with a minimum pulse period of 60 seconds between pulses (IEC 61000-4-5).  
Rated RMS Voltage, Rated DC Voltage: The maximum designated values of power system voltage that may be applied  
continuously between the terminals of a device.  
Varistor Voltage: Test characteristic that is used to classify varistors by type. A test current of 1mA DC is typically  
used to determine varistor voltage classification type. Varistor voltage clamping characteristics can be defined  
at various test levels.  
Rated Peak Single Pulse Transient Current: Maximum surge current, 8/20μs waveform which a varistor is rated to  
withstand for a single surge.  
Rated Single Pulse Transient Energy: Maximum allowable energy for a single impulse (see specified waveforms).  
Maximum Clamping Voltage: Measured peak voltage across the device terminals when a current impulse of specified  
amplitude and waveform is conducted through the varistor.  
Typical Capacitance: Typical capacitance values are measured at a test frequency of 1KHZ.  
General Characteristics  
Storage Temperature  
- 55° C to + 125° C  
125° C  
Operating Surface Temperature  
Operating Ambient Temperature  
- 55° C to + 85° C (without derating)  
Maximum Voltage-Temperature  
Coefficient  
< -0.01 % / °C  
Insulation Resistance  
Hi POT (Leads to Case, 1 min.)  
Typical Response Time  
Epoxy Rating  
1000 Megohm min.  
3000 VDC*  
< 15 nsec.  
94 V-0  
Current/Energy Derating (>85°C)  
DC Leakage Current  
Solderability  
- 2.5 % / °C  
200µA Max (at rated DC working voltage)  
MIL STD 202G, Method 208H  
Voltage change 10% from initially measured Varistor Voltage. When  
determining if varistor is within aforementioned criteria the same temperature  
must be observed as was used for initial Varistor Voltage measurements.  
Failure Criteria  
*Rating is for standard epoxy, for flame retardant coating (suffix “S”) disk sizes 5mm to 20mm rating is 2000 VDC, for disk  
sizes 22mm & 34mm rating is 2500VDC.  
WORLD PRODUCTS INC. 19654 Eighth Street East, Sonoma, CA 95476 | Phone (707) 996-5201 | Fax (707) 996-3380 | www.worldproducts.com  
Rev. 3.1  
2 | Metal Oxide Varistors - EV Series  
 复制成功!