欢迎访问ic37.com |
会员登录 免费注册
发布采购

WM8985 参数 Datasheet PDF下载

WM8985图片预览
型号: WM8985
PDF下载: 下载PDF文件 查看货源
内容描述: 多媒体编解码器, D类耳机和线路输出 [Multimedia CODEC With Class D Headphone and Line Out]
分类和应用: 解码器编解码器
文件页数/大小: 118 页 / 1498 K
品牌: WOLFSON [ WOLFSON MICROELECTRONICS PLC ]
 浏览型号WM8985的Datasheet PDF文件第48页浏览型号WM8985的Datasheet PDF文件第49页浏览型号WM8985的Datasheet PDF文件第50页浏览型号WM8985的Datasheet PDF文件第51页浏览型号WM8985的Datasheet PDF文件第53页浏览型号WM8985的Datasheet PDF文件第54页浏览型号WM8985的Datasheet PDF文件第55页浏览型号WM8985的Datasheet PDF文件第56页  
WM8985  
Pre-Production  
PEAK LIMITER  
To prevent clipping when a large signal occurs just after a period of quiet, the ALC circuit includes a  
limiter function. If the ADC input signal exceeds 87.5% of full scale (–1.16dB), the PGA gain is  
ramped down at the maximum attack rate (as when ALCATK = 0000), until the signal level falls  
below 87.5% of full scale. This function is automatically enabled whenever the ALC is enabled.  
Note: If ALCATK = 0000, then the limiter makes no difference to the operation of the ALC. It is  
designed to prevent clipping when long attack times are used.  
NOISE GATE (NORMAL MODE ONLY)  
When the signal is very quiet and consists mainly of noise, the ALC function may cause “noise  
pumping”, i.e. loud hissing noise during silence periods. The WM8985 has a noise gate function that  
prevents noise pumping by comparing the signal level at the input pins against a noise gate  
threshold, NGTH. The noise gate cuts in when:  
Signal level at ADC [dBFS] < NGTH [dBFS] + PGA gain [dB] + Mic Boost gain [dB]  
This is equivalent to:  
Signal level at input pin [dBFS] < NGTH [dBFS]  
The PGA gain is then held constant (preventing it from ramping up as it normally would when the  
signal is quiet).  
The table below summarises the noise gate control register. The NGTH control bits set the noise  
gate threshold with respect to the ADC full-scale range. The threshold is adjusted in 6dB steps.  
Levels at the extremes of the range may cause inappropriate operation, so care should be taken with  
set–up of the function. The noise gate only operates in conjunction with the ALC and cannot be used  
in limiter mode.  
REGISTER  
ADDRESS  
BIT  
LABEL  
DEFAULT  
000  
DESCRIPTION  
R35 (23h)  
2:0 NGTH  
Noise gate threshold:  
ALC Noise Gate  
Control  
000 = -39dB  
001 = -45dB  
010 = -51db  
011 = -57dB  
100 = -63dB  
101 = -70dB  
110 = -76dB  
111 = -81dB  
Noise gate function enable  
1 = enable  
3
NGATEN  
0
0 = disable  
Table 28 ALC Noise Gate Control  
The diagrams below show the response of the system to the same signal with and without noise  
gate.  
PP, Rev 3.4, October 2006  
52  
w
 复制成功!