欢迎访问ic37.com |
会员登录 免费注册
发布采购

WM8750-EV1M 参数 Datasheet PDF下载

WM8750-EV1M图片预览
型号: WM8750-EV1M
PDF下载: 下载PDF文件 查看货源
内容描述: 评估板用户手册 [Evaluation Board User Handbook]
分类和应用:
文件页数/大小: 48 页 / 1043 K
品牌: WOLFSON [ WOLFSON MICROELECTRONICS PLC ]
 浏览型号WM8750-EV1M的Datasheet PDF文件第1页浏览型号WM8750-EV1M的Datasheet PDF文件第2页浏览型号WM8750-EV1M的Datasheet PDF文件第3页浏览型号WM8750-EV1M的Datasheet PDF文件第4页浏览型号WM8750-EV1M的Datasheet PDF文件第6页浏览型号WM8750-EV1M的Datasheet PDF文件第7页浏览型号WM8750-EV1M的Datasheet PDF文件第8页浏览型号WM8750-EV1M的Datasheet PDF文件第9页  
WM8750-EV1M  
POWER SUPPLIES  
Using appropriate power leads with 4mm connectors, power supplies should be connected  
as described in Table 1.  
REF-DES  
SOCKET NAME  
SUPPLY  
+5V  
J8  
J2  
+5V  
DBVDD  
AVDD  
+1.8V to +3.6V  
+1.8V to +3.6V  
+1.42V to +3.6V  
+1.8V to +3.6V  
0V  
J4  
J10  
J47  
J1  
DCVDD  
HPVDD  
DGND  
AGND  
J5  
0V  
Table 1 Power Supply Connections  
The DGND and AGND connections may be connected to a common GND on the supply with  
no reduction in performance.  
To reduce the supply connections that need to be attached to the EVB, sites L1 and L8 are  
populated with 0R resistors shorting AVDD, HPVDD and DBVDD. In this configuration it is  
recommended that the supply only be attached to AVDD. If separate supplies are required  
the 0R resistors should be removed from sites L1 and L8.  
Note: Refer to WM8750 datasheet for limitations on individual supply voltages.  
Important: Exceeding the recommended maximum voltage can damage EVB  
components. Under voltage may cause improper operation of some or all of the EVB  
components.  
BOARD FUNCTIONALITY  
There are three options for inputting digital data into the WM8750 evaluation board. There is  
a coaxial input (J19) via a standard phono connector or an optical input (U3) via a standard  
optical receiver module. A direct digital input is also available via one side of a 2x8 pin  
header (H1).  
The analogue input signals are applied to the evaluation board via phono connectors J7  
(RLINE_IN1), J12 (LLINE_IN1), J14 (RLINE_IN2), J22 (LLINE_IN2), J26 (RLINE_IN3) and  
J45 (LLINE_IN3). Analogue inputs can also be applied to the evaluation board via 3.5mm  
jack sockets J9 (MIC_IN1); J16 (MIC_IN2) and J30 (MIC_IN3).  
There are two options for outputting digital data from the WM8750 evaluation board. There is  
a coaxial output (J29) via a standard phono connector. The digital signals may also be  
accessed via one side of a 2x8 pin header (H2).  
The analogue outputs of the board are via phono connectors J43 (ROUT1), J44 (LOUT1),  
J41 (LOUT2), J42 (ROUT2), J39 (MONO OUT) and J40 (OUT3). There is also an analogue  
output via a 3.5mm jack socket J46 (HP_OUT).  
All WM8750 device pins are accessible for easy measurement via the 2x4 pin headers (J13,  
J15, J17 and J21) running up each side of the device.  
Level-shift IC (U4) is used to shift the fixed +5V digital input from the CS8427 (U5) down to  
the same level as DBVDD and vice-versa.  
Rev 2.0, February 2005  
w
5