欢迎访问ic37.com |
会员登录 免费注册
发布采购

WM8716_08 参数 Datasheet PDF下载

WM8716_08图片预览
型号: WM8716_08
PDF下载: 下载PDF文件 查看货源
内容描述: 高性能24位, 192kHz的立体声DAC [High Performance 24-bit, 192kHz Stereo DAC]
分类和应用:
文件页数/大小: 26 页 / 507 K
品牌: WOLFSON [ WOLFSON MICROELECTRONICS PLC ]
 浏览型号WM8716_08的Datasheet PDF文件第2页浏览型号WM8716_08的Datasheet PDF文件第3页浏览型号WM8716_08的Datasheet PDF文件第4页浏览型号WM8716_08的Datasheet PDF文件第5页浏览型号WM8716_08的Datasheet PDF文件第7页浏览型号WM8716_08的Datasheet PDF文件第8页浏览型号WM8716_08的Datasheet PDF文件第9页浏览型号WM8716_08的Datasheet PDF文件第10页  
WM8716  
Production Data  
Notes:  
1. Ratio of output level with 1kHz full scale input, to the output level with all zeros into the digital input, measured ‘A’  
weighted over a 20Hz to 20kHz bandwidth.  
2. All performance measurements done with 20kHz low pass filter. Failure to use such a filter will result in higher THD+N  
and lower SNR and Dynamic Range readings than are found in the Electrical Characteristics. The low pass filter  
removes out of band noise; although it is not audible it may affect dynamic specification values.  
3. Except for Pin 12 (MODE8X) and Pin 17 (DIFFHW), where VIH = 2.6V min.  
TERMINOLOGY  
1. Signal-to-noise ratio (dB) (SNR) is a measure of the difference in level between the full-scale output and the output  
with no signal applied.  
2. Dynamic range (dB) (DNR) is a measure of the difference between the highest and lowest portions of a signal.  
Normally a THD+N measurement at 60dB below full scale. The measured signal is then corrected by adding the 60dB  
to it. (eg THD+N @ -60dB= -32dB, DR= 92dB).  
3. THD+N (dB) is a ratio of the r.m.s. values, of (Noise + Distortion)/Signal.  
4. Stop band attenuation (dB) is the degree to which the frequency spectrum is attenuated (outside audio band).  
5. Channel Separation (dB) (also known as Cross-Talk) is a measure of the amount one channel is isolated from the  
other. Normally measured by sending a full-scale signal down one channel and measuring the other.  
6. Pass-Band Ripple - Any variation of the frequency response in the pass-band region.  
LRCIN  
tBCH  
tBCL  
tLB  
BCKIN  
DIN  
tBCY  
tBL  
tDS  
tDH  
Figure 1 Audio Data Input Timing  
TEST CONDITIONS  
AVDD, DVDD = 5V, AGND, DGND = 0V, TA = +25oC, fs = 48kHz, SCKI = 256fs unless otherwise stated.  
PARAMETER  
SYMBOL  
TEST CONDITIONS  
MIN  
TYP  
MAX  
UNIT  
Audio Data Input Timing Information  
BCKIN pulse cycle time  
BCKIN pulse width high  
BCKIN pulse width low  
tBCY  
tBCH  
tBCL  
tBL  
100  
50  
ns  
ns  
ns  
ns  
50  
BCKIN rising edge  
to LRCIN edge  
30  
LRCIN rising edge  
tLB  
30  
ns  
to BCKIN rising edge  
DIN setup time  
DIN hold time  
tDS  
tDH  
30  
30  
ns  
ns  
w
PD, Rev 4.2,August 2008  
6