欢迎访问ic37.com |
会员登录 免费注册
发布采购

VCO600A622.080MHZ 参数 Datasheet PDF下载

VCO600A622.080MHZ图片预览
型号: VCO600A622.080MHZ
PDF下载: 下载PDF文件 查看货源
内容描述: 压控振荡器锯 [Voltage Controlled Saw Oscillator]
分类和应用: 振荡器压控振荡器
文件页数/大小: 6 页 / 118 K
品牌: VECTRON [ Vectron International, Inc ]
 浏览型号VCO600A622.080MHZ的Datasheet PDF文件第1页浏览型号VCO600A622.080MHZ的Datasheet PDF文件第2页浏览型号VCO600A622.080MHZ的Datasheet PDF文件第4页浏览型号VCO600A622.080MHZ的Datasheet PDF文件第5页浏览型号VCO600A622.080MHZ的Datasheet PDF文件第6页  
VCO-600A Voltage Controlled SAW Oscillator  
+5 V  
2,12,27  
+3V, 50ohms  
VCC  
VCO-600A  
0.5 to 4.5V  
23  
25  
19  
OUT  
OUT  
Control Voltage  
21  
Output Disable  
Test Clock In  
Optional  
Capacitor  
Reduces  
4
17  
VEE  
Ground  
Bandwidth  
10  
1,3,9,11,13,14,15,16,18,20,22,24,26,28  
Figure 1. PECL Operation  
-5 V  
-2V, 50ohms  
10  
VEE  
VCO-600A  
23  
25  
-4.5 to -0.5V  
19  
21  
OUT  
Control Voltage  
OUT  
Output Disable  
Test Clock In  
Optional  
Capacitor  
Reduces  
4
17  
VCC  
Ground  
Bandwidth  
2,12,27  
1,3,9,11,13,14,15,16,18,20,22,24,26,28  
Figure 2. ECL Operation  
1. By setting OD low, a test signal may be applied at CLKIN and fed through the VCO-600A to both the CLKOUT and CLKOUT to facilitate on board  
testing. The test signal input applied at CLKIN may be either an ECL or sinewave input (up to 1Vpp, AC coupled). CLKIN is biased internally to  
VBB (Vcc-1.3V)  
2. An optional capacitor to ground can be placed on VBW to reduce the modulation bandwidth for narrow bandwidth phase-lock loop applications. The  
modulation bandwidth will be approximately 1/(12000*C) Hz, where C is equal to the capacitance in Farads. If the optional capacitor is not utilized, VBW  
becomes a no connect (NC) and the modulation bandwidth will be approximately equal to the nominal device frequency ÷1200.  
3. By setting OD low, the outputs are disabled and CLKOUT is held Low while CLKOUT is held High. The threshold for OD is 1.4V above VEE. OD  
should not be driven above mid supply and during normal operation, should be left floating (use with an open collector or 3-State gate for interfacing with  
standard logic). If the OD feature is used during normal operation, then CLKIN should be tied through 10Kto GND to avoid any possibility of chatter on  
the CLKOUT outputs  
Vectron International 267 Lowell Rd, Hudson NH 03051-4916  
Tel:1-88-VECTRON-1  
e-mail vectron@vectron.com  
3