TSM917
ELECTRICAL CHARACTERISTICS
VCC = +5V, VEE = 0V, VIN+ = VREF, TA = -40°C to +85°C, unless otherwise noted. Typical values are at TA = +25°C.
See Note 1.
PARAMETER
SYMBOL CONDITIONS
MIN
TYP
MAX
UNITS
Inferred from the
PSRR test
Supply Voltage Range
VCC
TA = +25°C
1.8
5.5
V
VCC = 1.6V
TA = +25°C
TA = +25°C
TA = TMIN to TMAX
0.75
0.80
Supply Current
ICC
1.30
1.60
VCC + 0.2
5
μA
VCC = 5V
IN+ Voltage Range
VIN+
VOS
Inferred from the output swing test
VEE - 0.2
V
mV
mV
nA
TA = +25°C
TA = TMIN to TMAX
1
Input Offset Voltage
(Note 2)
10
Input-Referred Hysteresis
Input Bias Current
VHB
(Note 3)
TA = +25°C
4
0.15
1
2
1
IB
TA = TMIN to TMAX
VCC = 1.8V to 5.5V
VCC = 5V,
Power-Supply Rejection Ratio
PSRR
0.1
190
mV/V
TA = +25°C
400
500
200
300
400
500
200
300
ISOURCE = 8mA
VCC = 1.8V,
TA = TMIN to TMAX
TA = +25°C
Output-Voltage Swing High
Output-Voltage Swing Low
Output Short-Circuit Current
VCC - VOH
mV
mV
mA
55
190
55
ISOURCE = 1mA
TA = TMIN to TMAX
TA = +25°C
TA = TMIN to TMAX
TA = +25°C
TA = TMIN to TMAX
VCC = 5V
VCC = 1.8V
VCC = 5V, ISINK = 8mA
VOL
VCC = 1.8V,
ISINK = 1mA
95
8
Sourcing, VO = VEE
Sinking, VO = VCC
ISC
VCC = 5V
VCC = 1.8V
98
10
17
22
30
95
6
VCC = 1.8V
VCC = 5V
High-to-Low Propagation Delay
(Note 4)
Low-to-High Propagation Delay
(Note 4)
Rise Time
Fall Time
tPD-
µs
µs
VCC = 1.8V
VCC = 5V
tPD+
tRISE
tFALL
CL = 15pF
CL = 15pF
µs
µs
4
Power-Up Time
tON
1.2
ms
TA = +25°C
TA = TMIN to TMAX
1.227
1.200
1.245
1.263
1.290
Reference Voltage
VREF
V
Reference Voltage
Temperature Coefficient
Reference Output Voltage
Noise
TCVREF
en
95
ppm/°C
µVRMS
BW = 10Hz to 100kHz
BW = 10Hz to 100kHz, CREF = 1nF
600
215
Reference Line Regulation
Reference Load Regulation
∆VREF/ ∆VCC VCC = 1.8V to 5.5V
∆VREF/ ∆IOUT ∆IOUT = 10nA
0.1
mV/V
±0.2
mV/nA
Note 1: All specifications are 100% tested at TA = +25°C. Specification limits over temperature (TA = TMIN to TMAX) are guaranteed by
design, not production tested.
Note 2: VOS is defined as the center of the hysteresis band at the input.
Note 3: The hysteresis-related trip points are defined by the edges of the hysteresis band, measured with respect to the center of the
hysteresis band (i.e., VOS) (See Figure 2).
Note 4: Specified with an input overdrive (VOVERDRIVE) of 100mV, and load capacitance of CL = 15pF. VOVERDRIVE is defined above and
beyond the offset voltage and hysteresis of the comparator input. For the TSM917, reference voltage error should also be
added.
TSM917DS r1p0
Page 3
RTFDS
TOUCHSTONE [ TOUCHSTONE SEMICONDUCTOR INC ]
