SLRS027J – DECEMBER 1976 – REVISED JUNE 2010
www.ti.com
ABSOLUTE MAXIMUM RATINGS
(1)
at 25°C free-air temperature (unless otherwise noted)
MIN
V
CC
V
I
Collector-emitter voltage
Clamp diode reverse voltage
Input voltage
(2)
(2)
MAX
50
50
30
UNIT
V
V
V
mA
mA
A
Peak collector current
I
OK
Output clamp current
Total emitter-terminal current
See
and
500
500
–2.5
ULN200xA
T
A
Operating free-air temperature range
ULN200xAI
ULQ200xA
ULQ200xAT
D package
q
JA
Package thermal impedance
(3)
(4)
–20
–40
–40
–40
70
105
85
105
73
67
64
108
36
54
150
260
°C
°C
°C
°C/W
°C
N package
NS package
PW package
D package
N package
q
JC
T
J
T
stg
(1)
(2)
(3)
(4)
(5)
(6)
Package thermal impedance
(5)
(6)
Operating virtual junction temperature
Lead temperature for 1.6 mm (1/16 inch) from case for 10 seconds
Storage temperature range
–65
150
Stresses beyond those listed under "absolute maximum ratings" may cause permanent damage to the device. These are stress ratings
only, and functional operation of the device at these or any other conditions beyond those indicated under "recommended operating
conditions" is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
All voltage values are with respect to the emitter/substrate terminal E, unless otherwise noted.
Maximum power dissipation is a function of T
J
(max),
q
JA
, and T
A
. The maximum allowable power dissipation at any allowable ambient
temperature is P
D
= (T
J
(max) – T
A
)/q
JA
. Operating at the absolute maximum T
J
of 150°C can affect reliability.
The package thermal impedance is calculated in accordance with JESD 51-7.
Maximum power dissipation is a function of T
J
(max),
q
JC
, and T
A
. The maximum allowable power dissipation at any allowable ambient
temperature is P
D
= (T
J
(max) – T
A
)/q
JC
. Operating at the absolute maximum T
J
of 150°C can affect reliability.
The package thermal impedance is calculated in accordance with MIL-STD-883.
ELECTRICAL CHARACTERISTICS
T
A
= 25°C
PARAMETER
V
I(on)
V
CE(sat)
V
F
I
CEX
I
I(off)
I
I
I
R
C
i
On-state input voltage
Collector-emitter saturation voltage
Clamp forward voltage
Collector cutoff current
Off-state input current
Input current
Clamp reverse current
Input capacitance
TEST
FIGURE
TEST CONDITIONS
V
CE
= 2 V,
I
I
= 250
mA,
I
I
= 350
mA,
I
I
= 500
mA,
I
F
= 350 mA
V
CE
= 50 V,
V
CE
= 50 V,
T
A
= 70°C
V
CE
= 50 V,
V
I
= 17 V
V
R
= 50 V
V
I
= 0,
T
A
= 70°C
f = 1 MHz
I
I
= 0
I
I
= 0
V
I
= 6 V
I
C
= 500
mA
50
65
0.82
1.25
100
50
25
I
C
= 300 mA
I
C
= 100 mA
I
C
= 200 mA
I
C
= 350 mA
0.9
1
1.2
1.7
ULN2002A
MIN
TYP
MAX
13
1.1
1.3
1.6
2
50
100
500
mA
mA
mA
pF
mA
V
V
UNIT
V
4
Copyright © 1976–2010, Texas Instruments Incorporated
Product Folder Link(s):
TI [ TEXAS INSTRUMENTS ]
