欢迎访问ic37.com |
会员登录 免费注册
发布采购

TPS54231D 参数 Datasheet PDF下载

TPS54231D图片预览
型号: TPS54231D
PDF下载: 下载PDF文件 查看货源
内容描述: 2A , 28V输入,降压SWIFT ™ DC / DC转换器ECO- MODTM [2A, 28V INPUT, STEP DOWN SWIFT™ DC/DC CONVERTER WITH ECO-MODTM]
分类和应用: 转换器输入元件
文件页数/大小: 23 页 / 795 K
品牌: TI [ TEXAS INSTRUMENTS ]
 浏览型号TPS54231D的Datasheet PDF文件第3页浏览型号TPS54231D的Datasheet PDF文件第4页浏览型号TPS54231D的Datasheet PDF文件第5页浏览型号TPS54231D的Datasheet PDF文件第6页浏览型号TPS54231D的Datasheet PDF文件第8页浏览型号TPS54231D的Datasheet PDF文件第9页浏览型号TPS54231D的Datasheet PDF文件第10页浏览型号TPS54231D的Datasheet PDF文件第11页  
TPS54231  
www.ti.com .............................................................................................................................................................................................. SLUS851OCTOBER 2008  
TYPICAL CHARACTERISTICS (continued)  
OVERVIEW  
The TPS54231 is a 28-V, 2-A, step-down (buck) converter with an integrated high-side n-channel MOSFET. To  
improve performance during line and load transients, the device implements a constant frequency, current mode  
control which reduces output capacitance and simplifies external frequency compensation design. The  
TPS54231 has a pre-set switching frequency of 570 kHz.  
The TPS54231 needs a minimum input voltage of 3.5 V to operate normally. The EN pin has an internal pull-up  
current source that can be used to adjust the input voltage under-voltage lockout (UVLO) with two external  
resistors. In addition, the pull-up current provides a default condition when the EN pin is floating for the device to  
operate. The operating current is 75 µA typically when not switching and under no load. When the device is  
disabled, the supply current is 1 µA typically.  
The integrated 80 mhigh-side MOSFET allows for high efficiency power supply designs with continuous output  
currents up to 2 A.  
The TPS54231 reduces the external component count by integrating the boot recharge diode. The bias voltage  
for the integrated high-side MOSFET is supplied by an external capacitor on the BOOT to PH pin. The boot  
capacitor voltage is monitored by an UVLO circuit and will turn the high-side MOSFET off when the voltage falls  
below a preset threshold of 2.1 V typically. The output voltage can be stepped down to as low as the reference  
voltage.  
By adding an external capacitor, the slow start time of the TPS54231 can be adjustable which enables flexible  
output filter selection.  
To improve the efficiency at light load conditions, the TPS54231 enters a special pulse skipping Eco-modeTM  
when the peak inductor current drops below 100 mA typically.  
The frequency foldback reduces the switching frequency during startup and over current conditions to help  
control the inductor current. The thermal shut down gives the additional protection under fault conditions.  
DETAILED DESCRIPTION  
FIXED FREQUENCY PWM CONTROL  
The TPS54231 uses a fixed frequency, peak current mode control. The internal switching frequency of the  
TPS54231 is fixed at 570kHz.  
ECO-MODETM  
The TPS54231 is designed to operate in pulse skipping Eco-modeTM at light load currents to boost light load  
efficiency. When the peak inductor current is lower than 100 mA typically, the COMP pin voltage falls to 0.5 V  
typically and the device enters Eco-modeTM . When the device is in Eco-modeTM, the COMP pin voltage is  
clamped at 0.5 V internally which prevents the high side integrated MOSFET from switching. The peak inductor  
current must rise above 100 mA for the COMP pin voltage to rise above 0.5 V and exit Eco-modeTM. Since the  
integrated current comparator catches the peak inductor current only, the average load current entering  
Eco-modeTM varies with the applications and external output filters.  
VOLTAGE REFERENCE (Vref)  
The voltage reference system produces a ±2% initial accuracy voltage reference (±3.5% over temperature) by  
scaling the output of a temperature stable bandgap circuit. The typical voltage reference is designed at 0.8 V.  
BOOTSTRAP VOLTAGE (BOOT)  
The TPS54231 has an integrated boot regulator and requires a 0.1 µF ceramic capacitor between the BOOT and  
PH pin to provide the gate drive voltage for the high-side MOSFET. A ceramic capacitor with an X7R or X5R  
grade dielectric is recommended because of the stable characteristics over temperature and voltage. To improve  
drop out, the TPS54231 is designed to operate at 100% duty cycle as long as the BOOT to PH pin voltage is  
greater than 2.1 V typically.  
Copyright © 2008, Texas Instruments Incorporated  
Submit Documentation Feedback  
7
Product Folder Link(s): TPS54231