欢迎访问ic37.com |
会员登录 免费注册
发布采购

TMS320F28335ZHHA 参数 Datasheet PDF下载

TMS320F28335ZHHA图片预览
型号: TMS320F28335ZHHA
PDF下载: 下载PDF文件 查看货源
内容描述: 数字信号控制器(DSC ) [Digital Signal Controllers (DSCs)]
分类和应用: 微控制器和处理器外围集成电路数字信号处理器装置PC时钟
文件页数/大小: 195 页 / 2496 K
品牌: TI [ TEXAS INSTRUMENTS ]
 浏览型号TMS320F28335ZHHA的Datasheet PDF文件第124页浏览型号TMS320F28335ZHHA的Datasheet PDF文件第125页浏览型号TMS320F28335ZHHA的Datasheet PDF文件第126页浏览型号TMS320F28335ZHHA的Datasheet PDF文件第127页浏览型号TMS320F28335ZHHA的Datasheet PDF文件第129页浏览型号TMS320F28335ZHHA的Datasheet PDF文件第130页浏览型号TMS320F28335ZHHA的Datasheet PDF文件第131页浏览型号TMS320F28335ZHHA的Datasheet PDF文件第132页  
TMS320F28335, TMS320F28334, TMS320F28332  
TMS320F28235, TMS320F28234, TMS320F28232  
SPRS439IJUNE 2007REVISED MARCH 2011  
www.ti.com  
C10  
C9  
C8  
(A)  
XCLKIN  
C6  
C3  
C1  
C4  
C5  
(B)  
XCLKOUT  
A. The relationship of XCLKIN to XCLKOUT depends on the divide factor chosen. The waveform relationship shown is  
intended to illustrate the timing parameters only and may differ based on actual configuration.  
B. XCLKOUT configured to reflect SYSCLKOUT.  
Figure 6-5. Clock Timing  
6.8 Power Sequencing  
No requirements are placed on the power up/down sequence of the various power pins to ensure the  
correct reset state for all the modules. However, if the 3.3-V transistors in the level shifting output buffers  
of the I/O pins are powered prior to the 1.9-V transistors, it is possible for the output buffers to turn on,  
causing a glitch to occur on the pin during power up. To avoid this behavior, power the VDD pins prior to or  
simultaneously with the VDDIO pins, ensuring that the VDD pins have reached 0.7 V before the VDDIO pins  
reach 0.7 V.  
There are some requirements on the XRS pin:  
1. During power up, the XRS pin must be held low for tw(RSL1) after the input clock is stable (see  
Table 6-11). This is to enable the entire device to start from a known condition.  
2. During power down, the XRS pin must be pulled low at least 8 μs prior to VDD reaching 1.5 V. This is to  
enhance flash reliability.  
Additionally it is recommended that no voltage larger than a diode drop (0.7 V) should be applied to any  
pin prior to powering up the device. Voltages applied to pins on an unpowered device can bias internal  
P-N junctions in unintended ways and produce unpredictable results.  
6.8.1 Power Management and Supervisory Circuit Solutions  
Table 6-10 lists the power management and supervisory circuit solutions for 2833x/2823x devices. LDO  
selection depends on the total power consumed in the end application. Go to www.ti.com and click on  
Power Management for a complete list of TI power ICs or select the Power Management Selection Guide  
link for specific power reference designs.  
Table 6-10. Power Management and Supervisory Circuit Solutions  
SUPPLIER  
Texas Instruments  
Texas Instruments  
Texas Instruments  
Texas Instruments  
Texas Instruments  
Texas Instruments  
Texas Instruments  
Texas Instruments  
Texas Instruments  
TYPE  
LDO  
PART  
DESCRIPTION  
TPS767D301 Dual 1-A low-dropout regulator (LDO) with supply voltage supervisor (SVS)  
LDO  
TPS70202  
TPS766xx  
TPS3808  
TPS3803  
TPS799xx  
TPS736xx  
TPS62110  
TPS6230x  
Dual 500/250-mA LDO with SVS  
LDO  
250-mA LDO with PG  
SVS  
Open Drain SVS with programmable delay  
Low-cost Open-drain SVS with 5 μS delay  
200-mA LDO in WCSP package  
SVS  
LDO  
LDO  
400-mA LDO with 40 mV of VDO  
DC/DC  
DC/DC  
High Vin 1.2-A dc/dc converter in 4x4 QFN package  
500-mA converter in WCSP package  
128  
Electrical Specifications  
Copyright © 2007–2011, Texas Instruments Incorporated  
Submit Documentation Feedback  
Product Folder Link(s): TMS320F28335 TMS320F28334 TMS320F28332 TMS320F28235 TMS320F28234  
TMS320F28232  
 
 
 复制成功!