TMS320F28335, TMS320F28334, TMS320F28332
TMS320F28235, TMS320F28234, TMS320F28232
www.ti.com
SPRS439I–JUNE 2007–REVISED MARCH 2011
Table 2-3. Signal Descriptions (continued)
PIN NO.
ZHH
(1)
PGF/
PTP
PIN #
NAME
DESCRIPTION
ZJZ
BALL # BALL #
CLOCK
Output clock derived from SYSCLKOUT. XCLKOUT is either the same frequency, one-half
the frequency, or one-fourth the frequency of SYSCLKOUT. This is controlled by bits 18:16
(XTIMCLK) and bit 2 (CLKMODE) in the XINTCNF2 register. At reset, XCLKOUT =
SYSCLKOUT/4. The XCLKOUT signal can be turned off by setting XINTCNF2[CLKOFF]
to 1. Unlike other GPIO pins, the XCLKOUT pin is not placed in high-impedance state
during a reset. (O/Z, 8 mA drive).
XCLKOUT
XCLKIN
138
105
C11
J14
A10
G13
External Oscillator Input. This pin is to feed a clock from an external 3.3-V oscillator. In this
case, the X1 pin must be tied to GND. If a crystal/resonator is used (or if an external 1.9-V
oscillator is used to feed clock to X1 pin), this pin must be tied to GND. (I)
Internal/External Oscillator Input. To use the internal oscillator, a quartz crystal or a
ceramic resonator may be connected across X1 and X2. The X1 pin is referenced to the
1.9-V core digital power supply. A 1.9-V external oscillator may be connected to the X1 pin.
In this case, the XCLKIN pin must be connected to ground. If a 3.3-V external oscillator is
used with the XCLKIN pin, X1 must be tied to GND. (I)
X1
X2
104
102
J13
J11
G14
H14
Internal Oscillator Output. A quartz crystal or a ceramic resonator may be connected
across X1 and X2. If X2 is not used, it must be left unconnected. (O)
RESET
Device Reset (in) and Watchdog Reset (out).
Device reset. XRS causes the device to terminate execution. The PC will point to the
address contained at the location 0x3FFFC0. When XRS is brought to a high level,
execution begins at the location pointed to by the PC. This pin is driven low by the DSC
when a watchdog reset occurs. During watchdog reset, the XRS pin is driven low for the
watchdog reset duration of 512 OSCCLK cycles. (I/OD, ↑)
XRS
80
L10
M13
The output buffer of this pin is an open-drain with an internal pullup. It is recommended
that this pin be driven by an open-drain device.
ADC SIGNALS
ADCINA7
ADCINA6
ADCINA5
ADCINA4
ADCINA3
ADCINA2
ADCINA1
ADCINA0
ADCINB7
ADCINB6
ADCINB5
ADCINB4
ADCINB3
ADCINB2
ADCINB1
ADCINB0
ADCLO
35
36
37
38
39
40
41
42
53
52
51
50
49
48
47
46
43
57
54
K4
J5
K1
K2
L1
ADC Group A, Channel 7 input (I)
ADC Group A, Channel 6 input (I)
ADC Group A, Channel 5 input (I)
ADC Group A, Channel 4 input (I)
ADC Group A, Channel 3 input (I)
ADC Group A, Channel 2 input (I)
ADC Group A, Channel 1 input (I)
ADC Group A, Channel 0 input (I)
ADC Group B, Channel 7 input (I)
ADC Group B, Channel 6 input (I)
ADC Group B, Channel 5 input (I)
ADC Group B, Channel 4 input (I)
ADC Group B, Channel 3 input (I)
ADC Group B, Channel 2 input (I)
ADC Group B, Channel 1 input (I)
ADC Group B, Channel 0 input (I)
Low Reference (connect to analog ground) (I)
ADC External Current Bias Resistor. Connect a 22-kΩ resistor to analog ground.
External reference input (I)
L1
L2
L2
L3
L3
M1
N1
M3
K5
P4
N4
M4
L4
M1
M2
M3
N6
M6
N5
M5
N4
M4
N3
P3
N2
P6
P7
P3
N3
P2
M2
M5
L5
ADCRESEXT
ADCREFIN
Copyright © 2007–2011, Texas Instruments Incorporated
Introduction
25
Submit Documentation Feedback
Product Folder Link(s): TMS320F28335 TMS320F28334 TMS320F28332 TMS320F28235 TMS320F28234
TMS320F28232
TI [ TEXAS INSTRUMENTS ]
