ELECTRICAL CHARACTERISTICS: VS = ±5V
Boldface limits are tested at +25°C.
RF = 453Ω, RL = 100Ω, and G = +10, unless otherwise noted. See Figure 1 for AC performance.
OPA846ID, IDBV
TYP
MIN/MAX OVER TEMPERATURE
0
°
C to
–40
°
C to
MIN/
TEST
PARAMETER
CONDITIONS
+25°C
+25°C(1)
70°C(2)
+85°C(2)
UNITS
MAX LEVEL(3)
AC PERFORMANCE (see Figure 1)
Closed-Loop Bandwidth
G = +7, RG = 50Ω, VO = 200mVPP
G = +10, RG = 50Ω, VO = 200mVPP
G = +20, RG = 50Ω, VO = 200mVPP
G ≥ +40
500
400
110
1750
140
MHz
MHz
MHz
MHz
MHz
dB
typ
min
min
min
min
typ
C
B
B
B
B
C
270
82
1275
40
250
80
1245
36
225
75
1200
35
Gain Bandwidth Product (GBP)
Bandwidth for 0.1dB Gain Flatness
Peaking at a Gain of +7
Harmonic Distortion
G = +10, RL = 100Ω, VO = 200mVPP
G = +10, f = 5MHz, VO = 2VPP
RL = 100Ω
2nd-Harmonic
–76
–100
–109
–112
44
1.2
2.8
1.2
625
15
–70
–89
–95
–105
41
1.3
3.5
1.5
500
–68
–87
–92
–101
40
1.4
3.6
1.6
425
–66
–85
–90
–96
38
1.5
3.6
1.8
350
dBc
dBc
dBc
dBc
dBm
max
max
max
max
min
max
max
max
min
B
B
B
B
B
B
B
B
B
C
B
B
RL = 500Ω
RL = 100Ω
RL = 500Ω
3rd-Harmonic
2-Tone, 3rd-Order Intercept
Input Voltage Noise
Input Current Noise
Rise-and-Fall Time
Slew Rate
G = +10, f = 10MHz
f > 1MHz
√Hz
√Hz
nV/
pA/
f > 1MHz
0.2V Step
2V Step
2V Step
2V Step
2V Step
ns
V/µs
ns
ns
ns
Settling Time to 0.01%
0.1%
typ
max
max
10
6
12
8
14
10
16
12
1%
Differential Gain
Differential Phase
G = +10, NTSC, RL = 150Ω
G = +10, NTSC, RL = 150Ω
0.02
0.02
%
deg
typ
typ
C
C
DC PERFORMANCE(4)
Open-Loop Voltage Gain (AOL
Input Offset Voltage
Average Offset Voltage Drift
Input Bias Current
Input Bias Current Drift
Input Offset Current
)
VO = 0V
90
±0.15
±0.4
–10
±1
±0.1
±0.7
82
±0.60
±1.5
–19
±20
±0.35
±2
81
80
dB
mV
µV/°C
µA
nA/°C
µA
nA/°C
min
max
max
max
max
max
max
A
A
B
A
B
A
B
V
V
V
V
V
V
CM = 0V
CM = 0V
CM = 0V
CM = 0V
CM = 0V
CM = 0V
±0.68
±1.5
–19.8
±20
±0.45
±2
±0.70
±1.5
–21
±35
±0.60
±3.5
Input Offset Current Drift
INPUT
Common-Mode Input Range (CMIR)(5)
Common-Mode Rejection (CMR)
Input Impedance
±3.2
110
±3.0
95
±2.9
93
±2.8
90
V
dB
min
min
A
A
V
CM = ±1V, Input Referred
Differential-Mode
Common-Mode
V
V
CM = 0V
CM = 0V
6.6 || 2.0
4.7 || 1.8
kΩ || pF
MΩ || pF
typ
typ
C
C
OUTPUT
Output Voltage Swing
≥ 400Ω Load
100Ω Load
±3.4
±3.3
80
–80
0.002
±3.3
±3.2
65
±3.2
±3.0
61
±3.1
±2.9
60
V
V
mA
mA
Ω
min
min
min
min
typ
A
A
A
A
C
Current Output, Sourcing
Current Output, Sinking
Closed-Loop Output Impedance
V
V
O = 0V
O = 0V
–65
–61
–60
G = +10, f = 100kHz
POWER SUPPLY
Specified Operating Voltage
Maximum Operating Voltage
Maximum Quiescent Current
Minimum Quiescent Current
Power-Supply Rejection Ratio (–PSRR)
±5
V
V
mA
mA
dB
typ
max
max
min
min
C
A
A
A
A
±6
12.9
12.3
90
±6
13.0
12.1
88
±6
13.2
11.8
85
V
V
S = ±5V
S = ±5V
12.6
12.6
95
–VS = –4.5 to –5.5 (Input Referred)
THERMAL CHARACTERISTICS
Specified Operating Range: D, DBV Package
Thermal Resistance, θJA
–40 to +85
°C
typ
C
Junction-to-Ambient
D
SO-8
125
150
°C/W
°C/W
typ
typ
C
C
DBV SOT23-5
NOTES: (1) Junction temperature = ambient for +25°C min/max specifications. (2) Junction temperature = ambient at low temperature limit: junction temperature = ambient
+23°C at high temperature limit for over temperature min/max specifications. (3) Test Levels: (A) 100% tested at +25°C. Over temperature limits by characterization and
simulation. (B) Limits set by characterization and simulation. (C) Typical value only for information. (4) Current is considered positive out-of-node. VCM is the input common-
mode voltage. (5) Tested < 3dB below minimum specified CMR at ± CMIR limits.
OPA846
SBOS250C
3
www.ti.com
TI [ TEXAS INSTRUMENTS ]
