欢迎访问ic37.com |
会员登录 免费注册
发布采购

OPA4703UA 参数 Datasheet PDF下载

OPA4703UA图片预览
型号: OPA4703UA
PDF下载: 下载PDF文件 查看货源
内容描述: CMOS轨到轨输入/输出运算放大器 [CMOS, Rail-to-Rail, I/O OPERATIONAL AMPLIFIERS]
分类和应用: 运算放大器
文件页数/大小: 14 页 / 321 K
品牌: TI [ TEXAS INSTRUMENTS ]
 浏览型号OPA4703UA的Datasheet PDF文件第6页浏览型号OPA4703UA的Datasheet PDF文件第7页浏览型号OPA4703UA的Datasheet PDF文件第8页浏览型号OPA4703UA的Datasheet PDF文件第9页浏览型号OPA4703UA的Datasheet PDF文件第11页浏览型号OPA4703UA的Datasheet PDF文件第12页浏览型号OPA4703UA的Datasheet PDF文件第13页浏览型号OPA4703UA的Datasheet PDF文件第14页  
Power-supply pins should be bypassed with 1000pF ceramic  
capacitors in parallel with 1µF tantalum capacitors.  
APPLICATIONS INFORMATION  
OPA703 and OPA704 series op amps can operate on 160µA  
quiescent current from a single (or split) supply in the range  
of 4V to 12V (±2V to ±6V), making them highly versatile  
and easy to use. The OPA703 is unity-gain stable and offers  
1MHz bandwidth and 0.6V/µs slew rate. The OPA704 is  
optimized for gains of 5 or greater with a 3MHz bandwidth  
and 3V/µs slew rate.  
OPERATING VOLTAGE  
OPA703 and OPA704 series op amps are fully specified and  
guaranteed from +4V to +12V over a temperature range of  
–40ºC to +85ºC. Parameters that vary significantly with  
operating voltages or temperature are shown in the Typical  
Performance Curves.  
Rail-to-rail input and output swing helps maintain dynamic  
range, especially in low supply applications. Figure 1 shows  
the input and output waveforms for the OPA703 in unity-  
gain configuration. Operation is from a ±5V supply with a  
100kload connected to VS/2. The input is a 10Vp-p  
sinusoid. Output voltage is approximately 10Vp-p.  
RAIL-TO-RAIL INPUT  
The input common-mode voltage range of the OPA703 series  
extends 300mV beyond the supply rails at room temperature.  
This is achieved with a complementary input stage—an N-  
channel input differential pair in parallel with a P-channel  
differential pair, as shown in Figure 2. The N-channel pair is  
active for input voltages close to the positive rail, typically  
(V+) – 2.0V to 300mV above the positive supply, while the P-  
channel pair is on for inputs from 300mV below the negative  
supply to approximately (V+) – 1.5V. There is a small  
transition region, typically (V+) – 2.0V to (V+) – 1.5V, in  
which both pairs are on. This 500mV transition region can  
vary ±100mV with process variation. Thus, the transition  
region (both stages on) can range from (V+) – 2.1V to (V+)  
– 1.4V on the low end, up to (V+) – 1.9V to (V+) – 1.6V on  
the high end. Within the 500mV transition region PSRR,  
CMRR, offset voltage, and offset drift, and THD may vary  
compared to operation outside this region.  
G = +1, VS = ±5V  
Input  
Output (inverted on scope)  
200µs/div  
FIGURE 1. Rail-to-Rail Input and Output.  
V+  
VO  
VIN+  
VIN–  
V–  
FIGURE 2. Simplified Schematic.  
OPA703, OPA704  
10  
SBOS180A