PIN CONFIGURATION
ELECTROSTATIC
DISCHARGE SENSITIVITY
This integrated circuit can be damaged by ESD. Burr-Brown
recommends that all integrated circuits be handled with
appropriate precautions. Failure to observe proper handling
and installation procedures can cause damage.
Top View
SO-14
OPA4353
Out A
–In A
+In A
V+
1
2
3
4
5
6
7
14 Out D
13 –In D
12 +In D
11 V–
A
B
D
C
ESD damage can range from subtle performance degrada-
tion to complete device failure. Precision integrated circuits
may be more susceptible to damage because very small
parametric changes could cause the device not to meet its
published specifications.
+In B
–In B
Out B
10 +In C
9
8
–In C
Out C
ABSOLUTE MAXIMUM RATINGS(1)
Supply Voltage ................................................................................... 5.5V
Signal Input Terminals, Voltage(2) .................. (V–) – 0.3V to (V+) + 0.3V
Current(2) .................................................... 10mA
Output Short-Circuit(3) .............................................................. Continuous
Operating Temperature ..................................................–55°C to +125°C
Storage Temperature .....................................................–55°C to +125°C
Junction Temperature ...................................................................... 150°C
Lead Temperature (soldering, 10s)................................................. 300°C
NOTES: (1) Stresses above these ratings may cause permanent damage.
Exposure to absolute maximum conditions for extended periods may de-
grade device reliability. (2) Input terminals are diode-clamped to the power
supply rails. Input signals that can swing more than 0.3V beyond the supply
rails should be current-limited to 10mA or less. (3) Short circuit to ground,
one amplifier per package.
PACKAGE/ORDERING INFORMATION
PACKAGE
DRAWING
NUMBER(1)
SPECIFIED
TEMPERATURE
RANGE
PACKAGE
MARKING
ORDERING
NUMBER(2)
TRANSPORT
MEDIA
PRODUCT
PACKAGE
Single
OPA353NA
5-Lead SOT-23-5
331
"
182
"
–40°C to +85°C
D53
OPA353NA/250
OPA353NA/3K
OPA353UA
Tape and Reel
Tape and Reel
Rails
"
"
"
"
OPA353UA
SO-8 Surface Mount
–40°C to +85°C
OPA353UA
"
"
"
"
OPA353UA/2K5
Tape and Reel
Dual
OPA2353EA
MSOP-8 Surface Mount
337
"
182
"
–40°C to +85°C
E53
"
OPA2353UA
OPA2353EA/250
OPA2353EA/2K5
OPA2353UA
Tape and Reel
Tape and Reel
Rails
"
"
"
OPA2353UA
SO-8 Surface Mount
–40°C to +85°C
"
"
"
"
OPA2353UA/2K5
Tape and Reel
Quad
OPA4353EA
SSOP-16 Surface Mount
322
"
235
"
–40°C to +85°C
OPA4353EA
OPA4353EA/250
OPA4353EA/2K5
OPA4353UA
Tape and Reel
Tape and Reel
Rails
"
"
"
"
OPA4353UA
SO-14 Surface Mount
–40°C to +85°C
OPA4353UA
"
"
"
"
OPA4353UA/2K5
Tape and Reel
NOTES: (1) For detailed drawing and dimension table, please see end of data sheet, or Appendix C of Burr-Brown IC Data Book. (2) Models with a slash (/) are
available only in Tape and Reel in the quantities indicated (e.g., /2K5 indicates 2500 devices per reel). Ordering 2500 pieces of “OPA2353EA/2K5” will get a single
2500-piece Tape and Reel. For detailed Tape and Reel mechanical information, refer to Appendix B of Burr-Brown IC Data Book.
The information provided herein is believed to be reliable; however, BURR-BROWN assumes no responsibility for inaccuracies or omissions. BURR-BROWN assumes no responsibility
for the use of this information, and all use of such information shall be entirely at the user’s own risk. Prices and specifications are subject to change without notice. No patent rights or
licenses to any of the circuits described herein are implied or granted to any third party. BURR-BROWN does not authorize or warrant any BURR-BROWN product for use in life support
devices and/or systems.
®
3
OPA353, 2353, 4353
TI [ TEXAS INSTRUMENTS ]
