www.ti.com
MSP-TS430PZ100USB
Table B-25. MSP-TS430PZ5x100 Bill of Materials
No. per
Board
Pos.
Ref Des
Description
12pF, SMD0805
DigiKey Part No.
Comment
1
C1, C2
0
DNP
DNP: Only
1b
2
C3, C4
C6, C7
47pF, SMD0805
recommendation. Check
your crystal spec.
2
4
10uF/10V, Tantal Size B
511-1463-2-ND
C5, C10,
C11,
C12,C13,
C14
3
100nF, SMD0805
311-1245-2-ND
DNP: C12, C14
DNP
4
5
6
C8
C9
D1
0
1
1
2.2nF, SMD0805
470nF, SMD0805
green LED, SMD0805
478-1403-2-ND
67-1553-1-ND
DNP: headers and
receptacles enclosed with
kit. Keep vias free of
solder.: Header:
J1, J2, J3,
J4
"SAM1029-25-
NDSAM1213-25-ND"
7
0
25-pin header, TH
Receptacle
8
9
J5
1
6
3-pin header, male, TH
3-pin header, male, TH
SAM1035-03-ND
SAM1035-03-ND
JP5, JP6,
JP7,
JP8,JP9,
JP10
Place jumpers on pins 2-3
10
11
JP1, JP2
JP3
2
1
2-pin header, male, TH
3-pin header, male, TH
SAM1035-02-ND
SAM1035-03-ND
Place jumper on header
Place jumper on pins 1-2
Place on JP1, JP2, JP3,
JP5, JP6, JP7, JP8, JP9,
JP10
12
9
Jumper
15-38-1024-ND
13
14
JTAG
1
0
14-pin connector, male, TH HRP14H-ND
10-pin connector, male, TH
DNP: Keep vias free of
solder
BOOTST
Q1: Micro Crystal
MS1V-T1K 32.768kHz,
C(Load) = 12.5pF
DNP: Keep vias free of
solder
15
16
Q1, Q2
R3, R7
0
2
Crystal
330 Ω, SMD0805
541-330ATR-ND
541-000ATR-ND
541-47000ATR-ND
R1, R2, R4,
R6, R8, R9,
R10, R11,
R12
DNP: R6, R8, R9, R10,
R11, R12
17
3
0 Ω, SMD0805
18
19
20
R5
U1
1
1
1
47k Ω, SMD0805
Socket: IC357-1004-53N
90 x 82 mm
Manuf.: Yamaichi
2 layers
PCB
Rubber
standoff
Apply to corners at bottom
side
21
22
4
2
Select appropriate
DNP: Enclosed with kit
supplied by TI
MSP430
MSP430F5438IPZ
B.25 MSP-TS430PZ100USB
Due to the use of diodes in the power chain, the voltage on the MSP430F5xx device is approximately
0.3 V lower than is set by the debugging tool. Set the voltage in the IDE to 0.3 V higher than desired; for
example, to run the MCU at 3.0 V, set it to 3.3 V.
107
SLAU278F–May 2009–Revised December 2010
Hardware
Submit Documentation Feedback
© 2009–2010, Texas Instruments Incorporated
TI [ TEXAS INSTRUMENTS ]
