SLLS657C – APRIL 2005 – REVISED FEBRUARY 2009...................................................................................................................................................
www.ti.com
DESCRIPTION
The MAX3243E device consists of three line drivers, five line receivers, and a dual charge-pump circuit with
±15-kV ESD (HBM and IEC61000-4-2, Air-Gap Discharge) and ±8-kV ESD (IEC61000-4-2, Contact Discharge)
protection on serial-port connection pins. The device meets the requirements of TIA/EIA-232-F and provides the
electrical interface between an asynchronous communication controller and the serial-port connector. This
combination of drivers and receivers matches that needed for the typical serial port used in an IBM PC/AT, or
compatible. The charge pump and four small external capacitors allow operation from a single 3-V to 5.5-V
supply. In addition, the device includes an always-active noninverting output (ROUT2B), which allows
applications using the ring indicator to transmit data while the device is powered down. The device operates at
data signaling rates up to 250 kbit/s and a maximum of 30-V/µs driver output slew rate.
Flexible control options for power management are available when the serial port is inactive. The
auto-powerdown feature functions when FORCEON is low and FORCEOFF is high. During this mode of
operation, if the device does not sense a valid RS-232 signal, the driver outputs are disabled. If FORCEOFF is
set low, both drivers and receivers (except ROUT2B) are shut off, and the supply current is reduced to 1
µA.
Disconnecting the serial port or turning off the peripheral drivers causes the auto-powerdown condition to occur.
Auto-powerdown can be disabled when FORCEON and FORCEOFF are high, and should be done when driving
a serial mouse. With auto-powerdown enabled, the device is activated automatically when a valid signal is
applied to any receiver input. The INVALID output is used to notify the user if an RS-232 signal is present at any
receiver input. INVALID is high (valid data) if any receiver input voltage is greater than 2.7 V or less than –2.7 V
or has been between –0.3 V and 0.3 V for less than 30
µs.
INVALID is low (invalid data) if all receiver input
voltages are between –0.3 V and 0.3 V for more than 30
µs.
Refer to Figure 5 for receiver input levels.
The MAX3243EC is characterized for operation from 0°C to 70°C. The MAX3243EI is characterized for operation
from –40°C to 85°C.
ORDERING INFORMATION
T
A
SOIC – DW
SSOP – DB
TSSOP – PW
QFN – RHB
SSOP – DB
SOIC – DW
TSSOP – PW
QFN – RHB
(1)
(2)
PACKAGE
(1) (2)
Tape and reel
Tape and reel
Tape and reel
Tape and reel
Tape and reel
Tape and reel
Tape and reel
Tape and reel
ORDERABLE PART NUMBER
MAX3243ECDW
MAX3243ECDWR
MAX3243ECDB
MAX3243ECDBR
MAX3243ECPW
MAX3243ECPWR
MAX3243ECRHBR
MAX3243EIDB
MAX3243EIDBR
MAX3243EIDW
MAX3243EIDWR
MAX3243EIPW
MAX3243EIPWR
MAX3243EIRHBR
TOP-SIDE MARKING
MAX3243EC
MAX3243EC
MP243EC
MP243E
MAX3243EI
MAX3243EI
MP243EI
MR243E
0°C to 70°C
–40°C to 85°C
Package drawings, thermal data, and symbolization are available at
For the most current package and ordering information, see the Package Option Addendum at the end of this document, or see the TI
website at
2
Product Folder Link(s):
Copyright © 2005–2009, Texas Instruments Incorporated
TI [ TEXAS INSTRUMENTS ]
