SNOSBQ4D – MAY 1999 – REVISED MARCH 2013
These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam
during storage or handling to prevent electrostatic damage to the MOS gates.
ABSOLUTE MAXIMUM RATINGS
(1) (2) (3)
Supply Voltage Pin
Power Dissipation
V
8
V
3
V
3
Storage Temperature Range
Operating Temperature Range
LM567H
LM567CH, LM567CM, LM567CN
Soldering Information
PDIP Package
Soldering (10 sec.)
SOIC Package
Vapor Phase (60 sec.)
Infrared (15 sec.)
See
for other methods of soldering surface mount devices.
(1)
Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for
which the device is functional, but do not ensure specific performance limits. Electrical Characteristics state DC and AC electrical
specifications under particular test conditions which ensure specific performance limits. This assumes that the device is within the
Operating Ratings. Specifications are not ensured for parameters where no limit is given, however, the typical value is a good indication
of device performance.
If Military/Aerospace specified devices are required, please contact the Texas Instruments Sales Office/Distributors for availability and
specifications.
Refer to RETS567X drawing for specifications of military LM567H version.
The maximum junction temperature of the LM567 and LM567C is 150°C. For operating at elevated temperatures, devices in the TO-5
package must be derated based on a thermal resistance of 150°C/W, junction to ambient or 45°C/W, junction to case. For the DIP the
device must be derated based on a thermal resistance of 110°C/W, junction to ambient. For the SOIC package, the device must be
derated based on a thermal resistance of 160°C/W, junction to ambient.
215°C
220°C
260°C
−55°C
to +125°C
0°C to +70°C
(4)
9V
1100 mW
15V
−10V
V
4
+ 0.5V
−65°C
to +150°C
(2)
(3)
(4)
ELECTRICAL CHARACTERISTICS
AC Test Circuit, T
A
= 25°C, V
+
= 5V
Parameters
Power Supply Voltage Range
Power Supply Current Quiescent
Power Supply Current Activated
Input Resistance
Smallest Detectable Input Voltage
Largest No Output Input Voltage
Largest Simultaneous Outband Signal to
Inband Signal Ratio
Minimum Input Signal to Wideband Noise
Ratio
Largest Detection Bandwidth
Largest Detection Bandwidth Skew
Largest Detection Bandwidth Variation with
Temperature
Largest Detection Bandwidth Variation with
Supply Voltage
Highest Center Frequency
2
Product Folder Links:
4.75–6.75V
100
B
n
= 140 kHz
12
I
L
= 100 mA, f
i
= f
o
I
C
= 100 mA, f
i
= f
o
10
R
L
= 20k
R
L
= 20k
18
Conditions
LM567
Min
4.75
Typ
5.0
6
11
20
20
15
6
−6
14
1
±0.1
±1
500
±2
100
16
2
10
25
10
Max
9.0
8
13
15
LM567C/LM567CM
Min
4.75
Typ
5.0
7
12
20
20
15
6
−6
14
2
±0.1
±1
500
±5
18
3
25
Max
9.0
10
15
Units
V
mA
mA
kΩ
mVrms
mVrms
dB
dB
% of f
o
% of f
o
%/°C
%V
kHz
Copyright © 1999–2013, Texas Instruments Incorporated
TI [ TEXAS INSTRUMENTS ]
